Owner`s manual

• Volume Trim C)UOLLi"iE 7R]3"i
Use this feature to adjust tile level of the signal input at
each jack. This is useful if you want to balance the level of
each input source to avoid sudden changes in volume
when switching between input sources.
Choices: XM, TUNER, PHONO, CD, CD-R, MD/TAPE,
DVD, DTV, CBL/SAT, VCR 1, DVR/VCR 2,
V-AUX, DOCK, MULTI CH
Control range: 6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0.0 dB
L,iVLr ..... iR'fi
Xll ...8.SdB
TLINER ...8_OdE,
F'HONO ...8d_ldB
C:D ,. _8,, 8dl.:,
[ ,at [ _"] : UF'DcI_,_n
[43 '[>3 H_dJusq
This parameter also allects the signals output at ZONE OUT
jacks.
• Decoder mode [:,;,Di!!!(::ODERMODi!!!
Use to switch the input mode. You can designate the
reassigned digital input ,jacks for specific audio signals
(DTS, etc.).
Choices: AUTO, DTS
F ', F,.,=F M F,.,=F _,_=_d"F
+ {:D .... PLITO
DUI;..... gLITO
[>TO .... PUTO
C:BL!SFIT .... gUTO
[_]/['_] ILIp/Dowrl
• Multi channel input Setup
i::: ", Mi ii 1" 'r i"'i...i (::'i:::"F
Use to set the direction of the signals input into the center,
subwoofer and surround channels when a source
component is connected to the MUUI'I CH INPUT jacks.
If you input 8-channel signals from an external decoder,
use this feature to select.jacks for the additional front
signals.
I=',,NIii ,? F,H ==FT
iflb-i=_ L,N 2,Ci
+ E6H .......... LgST
I I/F'LIT CH ..... 6C:H
[.,_2 ['¢'] I UF [:,c,_,Jn
BGV B(!!ii...i
Use this feature to select the video source played it] the
background of the sources input from the MUUFI CH
INPUT jacks.
Choices: DVD, DTV, CBL/SAT, VCR, DVIUVCR 2,
V-AUX, LAST, OFF
• Select "LAST" to set this unit to automatically select
the last selected video source as the background video
source.
• Select "OFF" to set this unit not to play the video
source in the background.
Input channels ]]..iF:'ijT CH
Use this setting to select the number of channels input
fi'om an external decoder.
Choices: 6CH, 8CH
• Select "6CH" it'you input 6-channel signals.
• Select "8CH" if you input 8-channel signals.
• Select "AUTO" if you want this unit to automatically
detect input signal types and select the appropriate
input mode.
• Select "DTS" if you want this unit to select DTS as the
input mode.
If "ZONE2 AMP" is set to "[SPIF', "1SP21"or "BOTH" {see
page 100),no soundis output fl'om the surround back speakers
evenif you select "8CH". In this case, select "6CH" and setthe
output setting of the external component to 6 channels.
Front input FRONT
I=',,NIii T? F,H==FT
iflb-i=_ L,N2,Ci
E6H.......... LgST
I HF'UT C:H..... 8C:H
+ FROI4T ........ DUD
[.,k] ['¢-] IUF [:,o_,Jn
If you selected 8ch in "INPUT CH", you can select the
analog jacks at which the front signals from an external
decoder will be input.
Choices: MD/TAPE, CD-R, CD, DVD, DTV, CBL/SAT,
VCR1, DVR/VCR2, V-AUX
Note
"FRONT"parameter appears only x_henyou set "INPUT CH" to
"8CH".
96 En