Datasheet
Table Of Contents
- Contents
- Microbot Overview
- PICAXE Programming System
- Microbot Power Supply
- BOT120 Microbot Contents List
- The Microbric Connector
- Assembly 1 - Motherboard Panel
- Assembly 2 - Battery Box
- Assembly 3 - Motor Housing
- Assembly 4 - Motors
- Assembly 5 - Wheels, Tyres and Rear Skid
- Assembly 6 - Line Tracker
- Assembly 7 - Bumper Switches
- Assembly 8 - Pen Holder, Servo and SRF005 Modules
- Fully Assembled Microbot
- Motor Trouble Shooting
- Programming Software
- Programming Cable
- Download Hard Reset
- PICAXE-20X2 Pin Connections
- PICAXE-20X2 Microbot Pinout Table (Logicator)
- PICAXE-20X2 Microbot Pinout Table (Programming Editor / AXEpad)
- Programming Example 1 - LED Eyes
- Programming Example 2 - Push Button Switch
- Programming Example 3 - Bumper
- Programming Example 4 - Piezo Sounder
- Programming Example 5 - Motors
- Programming Example 6 - Line Tracker Testing
- Programming Example 7 - Line Tracker Program
- BOT121 Microbot Sensors Pack
- Assembly 9 - Infra-red Receiver (IR RX) Module
- Assembly 10 - Infra-red Transmitter (IR TX) Module
- Using the TVR010A Infra-red TV Style Remote
- Programming Example 8 - Infra-red Receiver
- Programming Example 9 - Infra-red Transmitter
- Assembly 11 - LDR Light Sensor Modules
- Programming Example 10 - Testing LDR Light Sensors
- Programming Example 11 - Light Follower
- SRF005 Ultrasonic Range Finder
- Assembly 12 - SRF005 Ultrasonic Range Finder
- Programming Example 12 - Testing SRF005
- Programming Example 13 - Using the SRF005
- BOT123 Servo Upgrade Pack
- Assembly 13 - BOT123 Servo / SRF005 Servo Adapter
- Programming Example 14 - Using Servos
- BOT127 Line Tracker / LED Upgrade Pack
- Appendix 1 - Home Made Sensors
- Appendix 2 - BOT120 Microbot Motherboard Schematic
- Appendix 3 - BOT120 Sensors Schematic
- Appendix 4 - BOT121 Sensors Pack Schematic
- Appendix 5 - BOT123 Servo Pack Schematic
- Appendix 6 - Advanced PIC (Non-PICAXE) Programming
- Appendix 7 - Copyright and Trademarks
- BOT110 Versabot - Microbot's 'big brother!'
15
revolution
(c) Copyright Revolution Education Ltd. Web: www.picaxe.co.uk Version 1.1 04/10
BOT120.PMD
BOT120 PICAXE-20X2 MICROBOT
Motor Trouble Shooting
If while using your Microbot you find that it does not move in a straight
line but instead turns to the left or right when it should be going straight,
or one motor seems to turn faster than the other, it may be that the
gearing within the motor housing is jamming.
Remember the gears also require a small drop of grease (a tube of grease
is supplied in the motherboard pack). The grease makes a huge
difference to performance, but only a small amount is required.
To un-jam a sticking gearbox simply push the motor in the direction
shown in the picture (push the motor towards the front). This should
remove pressure from the gearing and free-up the gearing.
In addition to checking
that the gearbox is not
jamming it is advisable to
check that the tyres are not
rubbing against the motor
mounts
Particularly check that
tyres have not become
dislodged and they are
evenly spread around the
wheel.
If a problem remains it may sometimes be overcome by swapping the
two motors. This requires removing the two motor and reassembling
with the motors on the opposite side that they were removed from.
While the motor housings
and motors are in pieces
check the motor terminals.
Flat terminals make poor
contact, so make sure the
contacts are angled.
Re-assemble and test your Microbot.