Installation & Assembly

ManualsBrandsRev-A-Shelf ManualsCloset & Bedroom Storage21.5"W - 26"W Closet Rod

TOOLS REQUIRED:

ESTIMATED

ASSEMBLY TIME:

20 MIN

CARE AND MAINTENANCE:

CLEAN WITH A DAMP CLOTH

AND WIPE PARTS DRY

INSTALLATION

INSTRUCTIONS

CPDR Series

(800) 626-1126

www.rev-a-shelf.com

PARTS LIST:

A FLAT HEAD B M3.5 SCREW

C M8 HEX BOLT

O RINGS

ALLEN WRENCH 1 GUIDE BLOCK AND DOWELS

STANDARD BUMPER

OMIT

12” BUMPER

TELESCOPING

HANGING ROD

PLASTIC HANDLE ENDCAP

ENDCAP PLASTIC BRACKET

HEAVY DUTY

BUMPER W/SCREWS

PULLDOWN

ARM

ASSEMBLY

TELESCOPING

HANDLE

Measure at least 34¾” (882.7mm) from the top of your closet panel.

By using the guide block and dowels, this will provide a platform to

ensure both arms are even on both sides.

For all other closet

depths (16 ” and

20”) you will install

at least 14” from the

rear of the closet.

If you are installing into a 12” or

14” depth closet you will install the

pull-down arm to the front edge of

the closet panel as shown.

12”, 14” DEPTH

16”, 20” DEPTH

x24

x1x2

34¾”

MINIMUM

14”

MINIMUM

I-CPDR-0414

GUIDE BLOCK

INSTALLATION INSTRUCTIONS: CPDR SERIES PULL-DOWN CLOSET ROD

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

CPDR SERIES PULL-DOWN CLOSET ROD

TOOLS REQUIRED:

20 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth and

wipe parts dry.

FLAT HEAD

SCREW

M3.5 SCREW

M8 HEX BOLT

O RINGS

ALLEN WRENCH 1 GUIDE BLOCK

WITH DOWELS

HEAVY DUTY

BUMPER W/ SCREWS

BUMPER

TELESCOPING

HANGING ROD

PLASTIC HANDLE

ENDCAP

PULL-DOWN

ARM

ASSEMBLY

TELESCOPING

HANDLE

x24

x1x2

Parts List:

(12” DEPTH

ONLY)

I-CPDR-0217

ENDCAP PLASTIC

BRACKET

Summary of content (4 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 CPDR SERIES PULL-DOWN CLOSET ROD TOOLS REQUIRED: ESTIMATED ASSEMBLY TIME: 20 MIN CARE AND MAINTENANCE: Clean with a damp cloth and wipe parts dry. (800) 626-1126 www.rev-a-shelf.com Parts List: FLAT HEAD SCREW M3.5 SCREW x2 x24 ALLEN WRENCH PARTSx1LIST: (A) FLAT HEAD x24 M8 HEX BOLT x2 TELESCOPING HANGING ROD O RINGS x5 1 GUIDE BLOCK WITH DOWELS PULL-DOWN ARM ASSEMBLY ALLEN WRENCH x1x2 x1 (B) M3.
PAGE 2
FIGURE 1 STEP 1 Measure at least 34 3/4” (882.7mm) from the top of your closet panel. By using the guide block and dowels, this will provide a platform to ensure both arms are even on both sides. 343/4” (882.7mm) MINIMUM GUIDE BLOCK STEP 2 If you are installing into a 12” or 14” depth closet you will install the pulldown arm assembly to the front edge of the closet panel as shown. (See Fig 2.1) For all other closet depths (16” and 20”) you will install at least 14” from the rear of the closet.
PAGE 3
FIGURE 3 STEP 3 Using the provided wood screws, install all of them except the last three screws in front. (See Fig 3) Repeat step 4 for other side. (Note: it is very important that both pull-down assemblies are lined up correctly with each other to ensure proper function. X X X STEP 4 Install the heavy duty stop using the provided screws. (See Fig 4) NOTE: This unit comes with two standard bumpers that are not used in this heavy dutyinstallation.
PAGE 4
lined up correctly with each other to ensure proper function. FIGURE 6 STEP 6 Attach the pull-down rod to the hanging rod and the plastic handle to the pull-down rod using M3.5 screws. (See Figure 6) Install the heavy duty stop as shown us Using the provided Install wood all ofusing theprovided screws that were thescrews, heavy dutyinstall stop as shown Using the provided wood install all except of provided screws AttachNOTE: the pull-down to the thescrews, (A) screws the last (3)thatinwere the front.