Installation Guide

Customer Service: 800-626-1126 | rev-a-shelf.com
8
Fije el mango telescópico a la varilla
colgante y la tapa del extremo del mango
de plástico al mango telescópico usando
los tornillos M3.5 (Véase la Fig. 8).
Fixez la poignée télescopique à la tige de
suspension et l’embout de poignée en
plastique à la poignée télescopique à l’aide
de vis M3,5 (voir la gure 8).
PASO 8 / ÉTAPE 8
Tire hacia abajo de los brazos izquierdo
y derecho para sujetar el conjunto de la
barra colgante a la unidad desplegable.
Usando los (2) pernos hexagonales M8
proporcionados y la llave Allen, coloque
la tapa de plástico en el extremo de cada
brazo (Véase la Fig. 9A).
Nota: La varilla colgante telescópica se
puede extender girando para desbloquear
y girando hacia atrás para trabarla en su
lugar (Véase la Fig. 9B).
Tirez les bras gauche et droit vers le bas pour
xer l’ensemble de la tige de suspension à
l’unité escamotable. À l’aide des (2) boulons
hexagonaux M8 fournis et d’une clé Allen,
xez l’embout en plastique à l’extrémité de
chaque bras (voir la gure 9A).
Remarque : La tringle de suspension
télescopique peut être allongée en la
tournant pour la déverrouiller et en la
tournant à nouveau pour la verrouiller (voir la
gure 9B).
Para sistemas de armario de 12” de
profundidad, se recomienda, pero no es
necesario, instalar los (2) topes provistos
(Véase la Fig. 10).
Pour les systèmes de meuble de 12 po de
profondeur, il est recommandé mais non
nécessaire d’installer les (2) butoirs fournis
(voir la gure 10).
PASO 9 / ÉTAPE 9
PASO 10 / ÉTAPE 10
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
FIGURE 8
FIGURE 9A
FIGURE 9B
FIGURE 10
3
Using the provided wood screws, install all of
the (A) screws except the last (3) in the front.
Install the heavy duty stop as shown using the
provided screws that were
included.
NOTE: this unit comes
with (2) standard bumpers that
are not used in this installation.
4
Attach the pull-down rod to the
hanging rod and the plastic handle to
the pull-down rod using the (B) screws.
6
Repeat step 4 for other side.
(Note: it is very important that
both pull-down assemblies are
lined up correctly with each other to
ensure proper function.
5
7
Pull down the left and right arms to attach the hanging rod
assembly to the pull-down unit. Using the (2) provided hex
bolts (C) and allen wrench attach plastic endcap to the end of
each arm as shown.
Note the hanging rod can be extended by
twisting motion to unlock and twisted back to lock into place.
For 12” depth
closet system, it
is recommended
but not necessary
to install the (2)
provided rubber
bumpers as shown.
3
Using the provided wood screws, install all of
the (A) screws except the last (3) in the front.
Install the heavy duty stop as shown using the
provided screws that were
included.
NOTE: this unit comes
with (2) standard bumpers that
are not used in this installation.
4
Attach the pull-down rod to the
hanging rod and the plastic handle to
the pull-down rod using the (B) screws.
6
Repeat step 4 for other side.
(Note: it is very important that
both pull-down assemblies are
lined up correctly with each other to
ensure proper function.
5
7
Pull down the left and right arms to attach the hanging rod
assembly to the pull-down unit. Using the (2) provided hex
bolts (C) and allen wrench attach plastic endcap to the end of
each arm as shown.
Note the hanging rod can be extended by
twisting motion to unlock and twisted back to lock into place.
For 12” depth
closet system, it
is recommended
but not necessary
to install the (2)
provided rubber
bumpers as shown.