Installation Guide

ManualsBrandsRev-A-Shelf ManualsWood Closet AccessoriesCPDR-2635

INSTALLATION INSTRUCTIONS: CPDR SERIES PULL-DOWN CLOSET ROD

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

CPDR SERIES PULL-DOWN CLOSET ROD

TOOLS REQUIRED:

20 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth and

wipe parts dry.

I-CPDR-1221

PARTS LIST

No. Description Qty.

A Flat Head Wood Screws 24

B M3.5 Screws 2

C Allen Wrench 1

D 1 Guide Block w/ Dowels 1

E Pull-down Arm Assembly 2

F Telescoping Handle 1

G M8 Hex Bolts 2

H O-Rings 5

I Bumper (12” Depth Only) 2

J Telescoping Hanging Rod 1

K Plastic Endcap Brackets 2

L Plastic Handle Endcap 1

M PDCR Arm Stop Bracket Bumpers 2

N PDCR Arm Stop Brackets (Left & Right) 2

O 8-32x50 Phillips Head Screws 2

P 8-32 Nylock Insert Lock Nuts 2

WATCH TUTORIALS OF OUR

PRODUCTS BEING INSTALLED

WWW.REV-A-SHELF.COM/VIDEOS

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 CPDR SERIES PULL-DOWN CLOSET ROD TOOLS REQUIRED: PARTS LIST No. Description Qty. A Flat Head Wood Screws 24 B M3.5 Screws 2 C Allen Wrench 1 D 1 Guide Block w/ Dowels 1 E Pull-down Arm Assembly 2 F Telescoping Handle 1 CARE AND MAINTENANCE: G M8 Hex Bolts 2 Clean with a damp cloth and wipe parts dry.
PAGE 2
FIGURE 1 STEP 1 Measure at least 34-3/4” (882.7mm) from the top of your closet panel. By using the guide block and dowels, this will provide a platform to ensure both arms are even on both sides (See Fig. 1). 343/4” (882.7mm) MINIMUM GUIDE BLOCK STEP 2 If you are installing into a 12” or 14” depth closet you will install the pulldown arm assembly to the front edge of the closet panel as shown. (See Fig.
PAGE 3
FIGURE 4 FIGURE 5 STEP 4 Place the bumper on the arm stop bracket (See Fig. 4). Note: This unit comes with two standard bumpers that are not used in this installation. STEP 5 Place (1) of the provided 8-32X50 Phillips Head screws into the opening (See Fig. 5). FIGURE 6 STEP 6 From the bottom of the screw, attach (1) of the 8-32 nuts to secure the screw and the bumper to the arm stop bracket (See Fig. 6). FIGURE 7 STEP 7 Affix the arm stop bracket using the provided screws (See Fig. 7).
PAGE 4
both pull-down assemblies are lined up correctly with each other to ensure proper function. FIGURE 8 STEP 8 6 Attach the telescoping handle to the hanging rod and the plastic handle endcap to the telescoping handle using M3.5 screws (See Fig. 8).
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN / INSTRUCTIONS D’INSTALLATION VARILLA PARA ARMARIO ABATIBLE SERIE CPDR TRINGLE DE PENDERIE ESCAMOTABLE DE LA SÉRIE CPDR Herramientas requeridas: Outils Requis: LISTA DE PARTES / LISTE DES PIÈCES Tiempo estimado de ensamblado: Durée de l’installation: 20 MIN CUIDADO/ ENTRETIEN: Limpie con un paño húmedo y seque las partes.
PAGE 6
FIGURE 1 PASO 1 / ÉTAPE 1 Mida al menos 34-3/4” (882.7 mm) desde la parte superior del panel de su armario. Al usar el bloque guía y los tacos, esto proporcionará una plataforma para garantizar que ambos brazos estén uniformes en ambos lados (Véase la Fig. 1). Mesurez au moins 882,7 mm (34-3/4 po) à partir du haut de votre panneau de placard. En utilisant le bloc guide et les chevilles, cela fournira une plateforme pour s’assurer que les deux bras sont égaux des deux côtés (voir la figure 1).
PAGE 7
FIGURE 4 FIGURE 5 PASO 4 / ÉTAPE 4 Coloque el tope en el soporte del tope del brazo (Véase la Fig. 4). Nota: Esta unidad viene con dos topes estándar que no se utilizan en esta instalación. Placez le butoir sur le support d’arrêt du bras (voir la figure 4). Remarque : Cette unité est livrée avec deux butoirs standard qui ne sont pas utilisés dans cette installation. PASO 5 / ÉTAPE 5 Coloque (1) de los tornillos de cabeza Phillips 8-32X50 proporcionados en la abertura (Véase la Fig. 5).
PAGE 8
3 4 5 FIGURE 8 PASO 8 / ÉTAPE 8 Fije el mango telescópico a la varilla colgante y la tapa del extremo del mango de plástico al mango telescópico usando los tornillos M3.5 (Véase la Fig. 8). Fixez la poignée télescopique à la tige de suspension et l’embout de poignée en plastique à la poignée télescopique à l’aide de vis M3,5 (voir la figure 8). PASO 9 / ÉTAPE 9 Tire hacia abajo de los brazos izquierdo y derecho para sujetar el conjunto de la barra colgante a la unidad desplegable.