Instructions / Assembly

ManualsBrandsRev-A-Shelf ManualsFor Home5PD-36CRN

INSTALLATION INSTRUCTIONS: 5PD SERIES PULL DOWN

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

5PD PREMIERE PULL-DOWN SHELVING SYSTEM

TOOLS REQUIRED:

45 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth

and wipe parts dry. Keep all

chemicals away from gas spring

piston rod.

I-5PD-TRI-0116

PART LIST:

(1) Left-mount bracket (A), (1) Right-mount

bracket (B), (1) Left-side frame (C),

(1) Right-side frame (D), (1)Handle (E),

(2) Wire basket (F), (1) Synchronization bar (G)

A 1 2 3 4

5 6 7 8

F G

Wood

Screws (10)

Washer

(4)

Cap Nut

(4)

1/4”x1-1/4”

Screws (4)

M5x12

Flat head

Screws (4)

Logo

Cover (4)

M4x6

Screws (4)

(6mm)

(2mm)

(6mm)

M5x12

Pan-head

screws (4)

20140328-1

Fittings

No.

Description Qty

1 1-1/4" x 1/4" Screw 4

1/4" Cap Nut

3 Washer

M5x12 (Pan Haed Screw)

Wood screw 16

M4x6 Screw

M5x12 (flat head Screw)

Logo Cover

Component

No.

Description Qty

A Base Left 1

Base Right

C Left kit 1

Right kit

E Handle 1

Wire Basket

Synchronization

H Bar 1

Large drawer

J Small drawer 2

Top bin

Long divider

M Short divider 2

1/3

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 5PD PREMIERE PULL-DOWN SHELVING SYSTEM Component Description No. TOOLS A #2 (6mm) 1 1 1 1 1 2 1 1 1 2 2 1 2 F Fittings Description No.
PAGE 2
Bottom Mounting STEP 1 FIG. Please refer to figure 1a, mark and drill pilot holes for the bottom mounting. 1a Mount the bottom mount brackets to the cabinet floor using qty (10) #8 wood screws. For heavy applications, it is recommended to add 1/4” bolts thru the brackets and cabinet floor. NOTE 24” shelf - inside cabinet width must be between 22-1/4” to 223/8” [564-568mm].
PAGE 3
STEP 3 Attach the two wire baskets to the side frames using qty (8) M5x8 pan head machine screws as shown in figure 3. Note: Screws may already be attached to brackets. Assembly FIG. FIG. 3 4 D F Attach the handle to the side frames using qty (2) M5x8 pan head machine screws as shown in figure 4. Note: Screws may already be attached to handle. Mount this assembly to the bottom mount brackets. The rear of the side frames will slide over a pin on the bottom mount brackets.
PAGE 4
STEP 5 Attach the synchronizer bar to the rear frame arms by tilting the bar at an angle and sliding it down the main body from front to back as shown in figure 6. Secure bar in place by using qty (4) M5x12 flat head screws as shown in figure 7. FIG. FIG. 6 7 #7 M5x12 Flat Head Machine Screws #2 #2 STEP 6 Operation OPEN Grab the handle and pull straight out. As the shelf system comes out of the cabinet, continue to pull out and down until the shelf system is locked in the down position.
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN INSTRUCTIONS D’INSTALLATION SISTEMA PREMIERE DE REPISAS PARA BAJAR 5PD 5PD PREMIER DE TABLETTES ESCAMOTABLES Component Description No. A #2 (6mm) 1 1 1 1 1 2 1 1 1 2 2 1 2 F Fittings Description No.
PAGE 6
Montaje Inferior Montage sur le Bas PASO 1 ÉTAPE 1 FIG. Por favor refiérase a la figura 1a, marque y taladre orificios piloto para el montaje inferior. Monte los soportes de montaje inferiores al piso del gabinete utilizando 10 tornillos de madera del número 8. Para aplicaciones pesadas, se recomienda añadir pernos de ¼” a través de los soportes y el piso del gabinete.
PAGE 7
Ensamble Assemblage PASO 3 ÉTAPE 3 Sujete las dos canastas de alambre a los lados del marco utilizando 8 tornillos de máquina del número M5x8 como se muestra en la figura 3. Nota: Los tornillos deben ya estar sujetos a los soportes. Sujete la manija a los lados del marco utilizando dos tornillos de máquina del M5x8 como se muestra en la figura 4. FIG. FIG. 3 4 D NOTA Los tornillos deben ya estar sujetos a la manija. Monte este ensamble a la parte inferior de los soportes de montaje.
PAGE 8
PASO 5 ÉTAPE 5 Sujete la barra de sincronización a los brazos de la parte posterior del marco, para hacer eso, incline la barra en ángulo y deslícela por debajo del cuerpo principal desde el frente hacia atrás como se muestra en la figura 6. Asegure la barra en su lugar usando cuatro tornillos de cabeza plana del M5x12 como se muestra en la figura 7. FIG. FIG.