Installation

ManualsBrandsRev-A-Shelf ManualsPull Out Trash CansRev-A-Shelf LEGRABOX Servo Drive Conversion Kit

INSTALLATION INSTRUCTIONS: 5LB SERIES LEGRABOX WASTE CONTAINER

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

5LB SERIES LEGRABOX WASTE CONTAINER

TOOLS REQUIRED:

30 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth and

wipe parts dry.

IMPORTANT NOTE - OPENING DIMENSIONS ARE CRITICAL

SINGLE WASTE CONTAINER UNITS ARE TO BE INSTALLED INTO CABINETS WITH A

13.5” OPENING. DOUBLE WASTE CONTAINER UNITS ARE TO BE INSTALLED INTO

CABINETS WITH A 16.5” OPENING.

I-5LB-1216

Parts List

No. Description Qty

1 Assembled Legrabox 1

2 Waste Container Divider Insert 1

3 Waste Container Bins 1-2

4 Waste Container Lids 1-2

5 Door Mount Brackets 2

6 RV Door Mount Screw Pack 2

7 5LB Slide Mounting Screw Pack 1

8 Rev-A-Shelf Logo Cover Caps 2

T20

5 6

x6 PER PACK

#6x 1/2”

#8x 1/2”

x8 PER PACK

WATCH VIDEO TUTORIALS OF

PRODUCT INSTALLATIONS

WWW.REV-A-SHELF.COM/VIDEOS

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 5LB SERIES LEGRABOX WASTE CONTAINER TOOLS REQUIRED: 4 3 #2 T20 2 1 ESTIMATED ASSEMBLY TIME: 30 MIN CARE AND MAINTENANCE: Clean with a damp cloth and wipe parts dry. Parts List No.
PAGE 2
NOTE: THE BELOW STEPS SHOW INSTALLATION INTO A FRAMELESS CABINET. IF INSTALLING INTO A FACE FRAME CABINET, YOUR CABINET SIDE WALLS WILL NEED TO BE MADE FLUSH WITH THE FACE FRAME USING A SCAB BOARD. CABINET OPENING DIMENSIONS REMAIN CRITICAL. STEP 1 FIGURE 1 Use the measurements (See Fig 1) to mark the slide mounting hole locations. It’s recommended to use an awl and rubber mallet for this step.
PAGE 3
STEP 4 FIGURE 4 Place the Rev-A-Shelf logo caps on both sides of the LEGRABOX (See Figure 4). STEP 5 Use the measurements (See Fig 5) to mark the door mounting hole locations with your awl and rubber mallet. FIGURE 5 32MM 32MM 96MM STEP 6 Install the door brackets to your door with the #6 x 1/2” screws included with the RV Door Mount screw pack (See Fig 6). NOTE: Make sure not to drill through your door.
PAGE 4
FIGURE 9 STEP 9 TILT ADJUSTMENT For inward/outward tilt adjustment, height adjustment and side adjustment of the drawer, use the corresponding adjustment locations (See Fig 9). HEIGHT ADJUSTMENT SIDE ADJUSTMENT T20 REMOVING THE DRAWER To remove the drawer, pull the drawer out, locate the triggers on the slides (See Fig 10), and squeeze them. Once the slides have disengaged, the drawer can be removed.
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN LES INSTRUCTIONS D’INSTALLATION CONTENEDOR DE BASURA DE LAS SERIES 5LB LEGRABOX POUBELLE DE LA SÉRIE 5LB LEGRABOX HERRAMIENTAS REQUERIDAS OUTILS REQUIS 4 3 #2 T20 2 1 TIEMPO ESTIMADO DE ENSAMBLADO: DURÉE DE L’INSTALLATION: 30-45 MIN CUIDADO: ENTRETIEN: Limpie con un paño húmedo y seque las partes. Nettoyer avec un chiffon humide et essuyer pour sécher complètement.
PAGE 6
NOTA: LOS SIGUIENTES PASOS MUESTRAN LA INSTALACIÓN DENTRO DE UN GABINETE SIN MARCO. SI ESTÁ INSTALANDO EN UN GABINETE CON MARCO, LAS PAREDES LATERALES DE SU GABINETE NECESITARÁN ESTAR AL RAZ CON LA CARA DEL MARCO USANDO UNA TABLA. LAS DIMENSIONES DE LA APERTURA DEL GABINETE CONTINÚAN SIENDO CRÍTICAS. REMARQUE: LES ÉTAPES CI-DESSUS MONTRENT UNE INSTALLATION DANS UNE ARMOIRE SANS CADRE.
PAGE 7
PASO 4 ÉTAPE 4 FIGURA 4 ILLUSTRATION 4 Coloque las tapas con el logotipo de Rev-A-Shelf en ambos lados del LEGRABOX (ver la figura 4). Placez les capuchons avec le logo Rev-AShelf sur les deux côtés du LEGRABOX (voir l’Illustration 4). PASO 5 ÉTAPE 5 Use las medidas (ver la figura 5) para marcar las ubicaciones de los orificios del montaje de la puerta con una lezna y un mazo de goma.
PAGE 8
PASO 9 ÉTAPE 9 FIGURA 9 ILLUSTRATION 9 AJUSTE DE INCLINACIÓN Para ajustes de inclinación hacia adentro o hacia afuera, ajuste de la altura, y ajuste lateral del cajón, use las ubicaciones de los ajustes correspondientes (ver la figura 9). Pour le réglage de l’inclinaison vers l’intérieur/vers l’extérieur, le réglage en hauteur et le réglage latéral du tiroir, utilisez les emplacements de réglage correspondants (voir l’Illustration 9).