Installation Guide

ManualsBrandsRev-A-Shelf ManualsPull Out Trash Cans30-Quart Plastic Soft Close Pull Out Trash Can

INSTALLATION INSTRUCTIONS: 5LB SERIES LEGRABOX WASTE CONTAINER

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

5LB SERIES LEGRABOX WASTE CONTAINER PULLOUTS

TOOLS REQUIRED:

30 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth and

wipe parts dry.

IMPORTANT NOTE - OPENING DIMENSIONS ARE CRUCIAL

SINGLE 35/50 QT. WASTE CONTAINER UNITS ARE TO BE INSTALLED INTO

CABINETS WITH A 13.5” OPENING. DOUBLE 35/50 QT. WASTE CONTAINER UNITS

ARE TO BE INSTALLED INTO CABINETS WITH A 16.5” OPENING. SINGLE 30 QT.

WASTE CONTAINER UNITS ARE TO BE INSTALLED INTO CABINETS WITH A 10.5”

OPENING.

I-5LB-1217

Parts List

No. Description Qty

1 Assembled LEGRABOX 1

2 Waste Container Divider Insert 1

3 Waste Container(s) 1-2

4 Waste Container Lid 1

5 Door Mount Brackets 2

6 RV Door Mount Screw Packs 2

7 5LB Slide Mount Screw Packs 1

8 Rev-A-Shelf Logo Cover Caps 2

T20

5 6

x6 PER PACK

#6x 1/2”

#8x 1/2”

x8 PER PACK

WATCH VIDEO TUTORIALS OF

PRODUCT INSTALLATIONS

WWW.REV-A-SHELF.COM/VIDEOS

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 5LB SERIES LEGRABOX WASTE CONTAINER PULLOUTS 4 TOOLS REQUIRED: #2 3 2 T20 1 ESTIMATED ASSEMBLY TIME: 30 MIN CARE AND MAINTENANCE: Clean with a damp cloth and wipe parts dry. WATCH VIDEO TUTORIALS OF PRODUCT INSTALLATIONS WWW.REV-A-SHELF.COM/VIDEOS Parts List No.
PAGE 2
NOTE: THE BELOW STEPS SHOW INSTALLATION INTO A FRAMELESS CABINET. IF INSTALLING INTO A FACE FRAME CABINET, YOUR CABINET SIDE WALLS WILL NEED TO BE MADE FLUSH WITH THE FACE FRAME USING A SCAB BOARD. CABINET OPENING DIMENSIONS REMAIN CRUCIAL. STEP 1 FIGURE 1 Use the measurements from Figure 1 to mark the slide mounting hole locations. (recommended with an awl and rubber mallet).
PAGE 3
STEP 4 FIGURE 4 Place the Rev-A-Shelf logo caps on both sides of the LEGRABOX (See Fig 4). STEP 5 Use the measurements from Figure 5 to mark the door mounting hole locations (recommended with an awl and rubber mallet). FIGURE 5 1-1/4” (32 mm) 1-1/4” (32 mm) 3-25/32” (96 mm) STEP 6 Install the door brackets to the door with the #6 x 1/2” screws included with the RV Door Mount screw pack (See Fig 6). NOTE: Make sure not to drill through the door.
PAGE 4
FIGURE 9 STEP 9 TILT ADJUSTMENT For inward/outward tilt adjustment, height adjustment and side adjustment of the LEGRABOX, use the corresponding adjustment locations (See Fig 9). HEIGHT ADJUSTMENT SIDE ADJUSTMENT T20 REMOVING THE LEGRABOX To remove the LEGRABOX, pull the drawer out, locate the triggers on the slides (See Fig 10), and squeeze them. Once the slides have disengaged, the LEGRABOX can be removed.
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN LES INSTRUCTIONS D’INSTALLATION CONTENEDOR DE BASURA DE LAS SERIES 5LB LEGRABOX POUBELLE DE LA SÉRIE 5LB LEGRABOX 4 HERRAMIENTAS REQUERIDAS OUTILS REQUIS #2 3 2 T20 1 TIEMPO ESTIMADO DE ENSAMBLADO: DURÉE DE L’INSTALLATION: 30-45 MIN CUIDADO: ENTRETIEN: Limpie con un paño húmedo y seque las partes. Nettoyer avec un chiffon humide et essuyer pour sécher complètement.
PAGE 6
NOTA: LOS SIGUIENTES PASOS MUESTRAN LA INSTALACIÓN DENTRO DE UN GABINETE SIN MARCO. SI ESTÁ INSTALANDO EN UN GABINETE CON MARCO, LAS PAREDES LATERALES DE SU GABINETE NECESITARÁN ESTAR AL RAZ CON LA CARA DEL MARCO USANDO UNA TABLA. LAS DIMENSIONES DE LA APERTURA DEL GABINETE CONTINÚAN SIENDO CRÍTICAS. REMARQUE: LES ÉTAPES CI-DESSUS MONTRENT UNE INSTALLATION DANS UNE ARMOIRE SANS CADRE.
PAGE 7
PASO 4 ÉTAPE 4 FIGURA 4 ILLUSTRATION 4 Coloque las tapas con el logotipo de Rev-A-Shelf en ambos lados del LEGRABOX (ver la figura 4). Placez les capuchons avec le logo Rev-AShelf sur les deux côtés du LEGRABOX (voir l’Illustration 4). PASO 5 ÉTAPE 5 Use las medidas (ver la figura 5) para marcar las ubicaciones de los orificios del montaje de la puerta con una lezna y un mazo de goma.
PAGE 8
PASO 9 ÉTAPE 9 FIGURA 9 ILLUSTRATION 9 AJUSTE DE INCLINACIÓN Para ajustes de inclinación hacia adentro o hacia afuera, ajuste de la altura, y ajuste lateral del cajón, use las ubicaciones de los ajustes correspondientes (ver la figura 9). Pour le réglage de l’inclinaison vers l’intérieur/vers l’extérieur, le réglage en hauteur et le réglage latéral du tiroir, utilisez les emplacements de réglage correspondants (voir l’Illustration 9).