Instructions / Assembly

Customer Service: 800-626-1126 | rev-a-shelf.com
2
Remove the soft-close
mechanism as shown in Figure
1A. Attach the slide feet to the
bottom of the slide using (4)
M4 screws (See Fig. 1B).
NOTE: You will need to
remove the inner member(s)
from the slide so you have
a hollow channel when
attaching the feet.
STEP 1
Place the Bottom Slide
Template in the bottom of your
cabinet as shown in Figure
2A. Mark (12) hole locations
as shown on the template and
drill 1/8” pilot holes. Align the
front of the slide with the front
of the face frame and center
the slide in the cabinet. Attach
to the oor using (8) #8 1”
wood screws (See Fig. 2B).
NOTE: When using the
template to align the pilot
holes, be sure to fold along
the dotted line on the front
of the template to wrap over
the face frame or front end
of the frameless cabinet. This
will keep your slide from
being installed too far back
into the cabinet.
STEP 2
The top slide of the pantry
needs to be mounted ush
with the face frame. To do
so, it may be necessary to cut
and attach a spacer board as
shown in Figure 3.
STEP 3
FIGURE 1A FIGURE 1B
FIGURE 2A
FIGURE 3
(A)
MEASURE FACE
FRAME WIDTH
CORRESPONDING SPACER
BOARD DIMENSIONS
AT LEAST 8”
(B)
MEASURE
CABINET
DEPTH
(A)
(B)
(A)
MEASURE FACE
FRAME WIDTH
CORRESPONDING SPACER
BOARD DIMENSIONS
AT LEAST 8”
(B)
MEASURE
CABINET
DEPTH
(A)
(B)
FACE FRAME CABINETS
Install bottom slide
1) Attach feet (#9) to bottom slide (C) using M4 screw (#8) as shown
in
eb ot deen lliw esolc-tfos eht ,toof raer eht hcatta oT .1
to remove the inner member(s) from the slide so you have a hollow
channel when attaching the feet.
Install top slide
3) The top slide (B) of the pantry needs to be mounted with the
draob recaps a hcatta dna tuc ot yrassecen eb ylekil lliw tI .emarf ecaf
as shown in
3.
Insert pantry frame
5) The bottom of the frame (A) sits on top of the bottom slide (C) as
shown in
.hcatta ot )3#( rehsaw dna )2#( wercs 6M esU .5
6) Slide the top portion of the frame up so that the top slide is
concealed but not touching the wood cabinet.
7) Two pins in top slide (B) insert into mating bushings in the top of
the frame (A) as shown in
6.
8) Tighten the two screws in 7.
C
B
B A
3
Top Spacer
Must be
with Face Frame
4) Using 4, mark 3 hole locations and drill ⁄ ” pilot holes.
Roughly align the front of the slide with the front of the face frame
morf draob recaps eht ot hcattA .tenibac eht ni edils eht retnec dna
step 3 using screws (#6).
2) Mark 12 hole locations and drill ⁄ eht ngila ylhguoR .seloh tolip ”
front of the slide with the front of the face frame and center the slide
eht ot hcattA .tenibac eht ni
using screws (#7). When using the
template to align the pilot hole, be sure to fold across the dotted line
on the front of the template to wrap over the face frame or front end
of the frameless cabinet. This will keep your slide from being installed
too far back into the cabinet. See
2.
A
C
A
C
(25)
(60)
(120)
(60)
(60)
(190)
(160)
(160)
(40)
UNIT : inch (mm)
1
8
#2
FIGURE 2B
CENTERLINE
cutting line for small cabinet
cutting line for small cabinet
FRONT SIDE (DOOR)
IJģ
ĩijĶĪ
ijĮĴİĹģ
ĩķıĪ
IJĮĴİĴijģ
ĩijĹĪ
ĵĮĴİĵģ
ĩIJijıĪ
ijĮĴİĹģ
ĩķıĪ
ĸĮIJİijģ
ĩIJĺıĪ
ijĮĴİĹģ
ĩķıĪ
5300/5700 SERIES PULLOUT PANTRY BOTTOM SLIDE TEMPLATE
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
T-5700-BTM-0117