Installation Guide
3INSTALLATION INSTRUCTIONS: 5730/5786 SERIES PULLOUT BASKET WITH SOFT–CLOSE
A
B
C
D
E
Datum point
Bottom dimension
12CR /15CR / 21CR / 30CR / 33CR
210 / 8
9
/
32
”
1
5
/
32
”
40
mm
164
mm
/ 241
mm
/ 393
mm
/ 623
mm
/ 699
mm
D
D
E
F G
A
B
6
1
/
2
”
9
1
/
2
”
15
1
/
2
”
24
17
/
64
”
27
17
/
64
”
H
A
(5730)
(5786)
I
J
J
I
Attach slide half of side-mount
bracket to front of slide with two
screws per slide. Front screw
should use the fourth top hole
from the front of the slide.
Mark fourth hole locations
on cabinet wall per Flank
Dimension Diagram. Align
cabinet half of side-mount
bracket holes with marked
locations and install with four
screws. Repeat on opposite wall.
Place slide assembly on top of
cabinet mount bracket, insert
screws, adjust to the desired
width of basket and tighten
screws. Repeat on opposite wall.
NOTE
If door mounting, skip to door
mount instructions.
For Inset-Door applications,
move the side-mount bracket
back the thickness of the door.
OPTIONAL MOUNTING
Flip the two brackets to make an
“S” shape to avoid door hinges
or for additional space
STEP 1
Snap two logo caps to the studs
on the front side of the basket.
Place basket on top of slides and
push back until the basket locks
under the tab at the rear and the
button on the side.
NOTE
You should hear the button click
when engaged.
STEP 2
A
B
C
D
E
Datum point
Bottom dimension
12CR /15CR / 21CR / 30CR / 33CR
210 / 8
9
/
32
”
1
5
/
32
”
40
mm
164
mm
/ 241
mm
/ 393
mm
/ 623
mm
/ 699
mm
D
D
E
F G
A
B
6
1
/
2
”
9
1
/
2
”
15
1
/
2
”
24
17
/
64
”
27
17
/
64
”
H
A
(5730)
(5786)
I
J
J
I
Side Mounted:
For Face-Frame Cabinets
Front
Back
38
mm
min
1
49
/
64
”
88
mm
64
mm
64
mm
B
C
C
A
Flank Dimension
E
1
1
/
2
”
2
17
/
64
”
3
1
/
2
”
2
17
/
64
”
45
mm
J
I
J
* Add door thickness
for Inset cabinets
Front
Back
38
mm
min
1
49
/
64
”
88
mm
64
mm
64
mm
B
C
C
A
Flank Dimension
E
1
1
/
2
”
2
17
/
64
”
3
1
/
2
”
2
17
/
64
”
45
mm
J
I
J
Front
Back
38
mm
min
1
49
/
64
”
88
mm
64
mm
64
mm
B
C
C
A
Flank Dimension
E
1
1
/
2
”
2
17
/
64
”
3
1
/
2
”
2
17
/
64
”
45
mm
J
I
J
Front
Back
38
mm
min
1
49
/
64
”
88
mm
64
mm
64
mm
B
C
C
A
Flank Dimension
E
1
1
/
2
”
2
17
/
64
”
3
1
/
2
”
2
17
/
64
”
45
mm
J
I
J
Note: Inside cabinet widths can be as follows:
12CR = 13
11
/32” [339mm] – 13.68” [348mm]
15CR = 16
11
/32” [415mm] – 16.68” [424mm]
21CR = 22
11
/32” [567mm] – 22.68” [576mm]
30CR = 31
25
/64” [797mm] – 31.73” [806mm]
33CR = 34
3
/8” [873mm] – 34.72” [882mm]
I-57XX-0915