Installation Guide
1) Refer to Figure 1 for measurements, depending on your cabinet construc-
tion, your dimensions may be dierent than the ones shown. The cabinet
image in Figure 1 is a Frameless cabinet with an overlay door. Once all 11
location(s) have been marked, pre-drill using the 1/16” drill bit.
• Attach Inside Frame (A) to the cabinet oor and side walls using 8 of the
5/32X18MM Wood Screws (#5). Use your Level to ensure Inside Frame (A) is
balanced. Tighten the 4 bolts on top of Inside Frame (A) to lock brackets to
the cabinet sides.
• Attach Adjustable Side Bracket (K) to the cabinet wall using 3 of the
5/32X18MM Wood Screws (#5).
A
B
C
D
E
F
G
8
7
5
6
4
3
1
2
H
I
J
1
1
1
1
1
2
1
2
2
30
1
1
2
2
1
H
D
C
7
6
9
J
4
1
1
A
8
9
10
1
G
E
5
4
2
F
2
I
B
3
3
A
10
2
K
1
K
H
F
B
4
K
QTY
Description
Description
PANELS CHECK LIST
FITTINGS CHECK LIST
Inside Frame
Swivel Frame
Up Bracket
Support
Bottom holder
Screw
Screw
Connecter
Large Basket
Small Basket
Plastic cover
Screw
Screw
Gas Spring
Bracket
QTY
Outside frame
Bracket
*pre-installed
Screw
Down Bracket
Stopper
Adjustable Bracket
After adjusting, lock 4
sides screw tightly.
39” - 48” (990-1219mm)
A
B
C
D
E
F
G
8
7
5
6
4
3
1
2
H
I
J
1
1
1
1
1
2
1
2
2
30
1
1
2
2
1
H
D
C
7
6
9
J
4
1
1
A
8
9
10
1
G
E
5
4
2
F
2
I
B
3
3
A
10
2
K
1
K
H
F
B
4
K
QTY
Description
Description
PANELS CHECK LIST
FITTINGS CHECK LIST
Inside Frame
Swivel Frame
Up Bracket
Support
Bottom holder
Screw
Screw
Connecter
Large Basket
Small Basket
Plastic cover
Screw
Screw
Gas Spring
Bracket
QTY
Outside frame
Bracket
*pre-installed
Screw
Down Bracket
Stopper
Adjustable Bracket
2) Attach the Swivel Frame (B) to the Adjustable Side Bracket (K) using 3 of
the M5x8 Hex Flange Cross Bolt(s) (#11). For both Face Frame and Frameless
cabinets with overlay style doors, Swivel Frame (B) must be sitting ush
with the front of the cabinet frame. If an inset door application is being
used, Swivel Frame (B) must be installed back from the cabinet frame front
the thickness of the door panel. Once aligned properly for your cabinet
application, rst secure the 3 M5x* Hex Flange Cross Bolt(s) (#11) and then
use 2 of the 5/32X18MM Wood Screws (#5) and secure Swivel Frame (B) to
the cabinet oor.
A
B
C
D
E
F
G
8
7
5
6
4
3
1
2
H
I
J
1
1
1
1
1
2
1
2
2
30
1
1
2
2
1
H
D
C
7
6
9
J
4
1
1
A
8
9
10
1
G
E
5
4
2
F
2
I
B
3
3
A
10
2
K
1
K
H
F
B
4
K
QTY
Description
Description
PANELS CHECK LIST
FITTINGS CHECK LIST
Inside Frame
Swivel Frame
Up Bracket
Support
Bottom holder
Screw
Screw
Connecter
Large Basket
Small Basket
Plastic cover
Screw
Screw
Gas Spring
Bracket
QTY
Outside frame
Bracket
*pre-installed
Screw
Down Bracket
Stopper
Adjustable Bracket
3) Attach the Support Arm (H) to the bottom of Swivel Frame (B) using the
2 M6x12mm Button Head Screws (#4). Pull Swivel Frame (B) to the open po-
sition to allow for better access to the threaded holes. Now, Locate the two
hole indentions on the bottom of Swivel Frame (B), align Bottom Holder (F)
to the hole locations and then attach Bottom Holder (F) to the cabinet oor
using 2 of the 5/32x 18MM Wood Screws (#5)
• You do not need to attach Bottom Holder (F) to Swivel Frame (B), screws
are NOT provided for this.
4) Refer to gure 2, Door Dimensions, to begin marking your
door panel for mounting. WARNING: ALL DOOR MOUNTING
LOCATIONS MUST BE IN THE THICK PANEL OF YOUR DOOR!
Use your 1/16” Drill Bit and pre-drill your door mount hole
markings. Place Up Bracket (D) into the top of Door Frame (C)
and place Down Bracket (E) into the bottom of Door Frame (C).
Attach Door Frame (C) to the back of your door using 4 of the
5/32x18MM Wood Screws (#5). Use your Phillips head screw
driver and tighten all 8 pre-installed fasteners.
7
6
7
9
I
H
6
7
B
C
G
H
3
3
10
C
E
D
G
1
F
B
B
B
5
5
5
5
5
5
5
5
5
5
5
5
11
11
11