Installation Guide

ManualsBrandsRev-A-Shelf ManualsPull Out Trash Cans35-Quart Plastic Soft Close Pull Out Trash Can

Top mount

waste container

Top mount

waste container

Top mount

waste container

Top mount

waste container

Top mount

waste container

Top mount

waste container

Top mount

waste container

Top mount

waste container

Top mount

waste container

INSTALLATION INSTRUCTIONS: 53TM STAINLESS STEEL TOP MOUNT WASTE CONTAINER

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

53TM SERIES STAINLESS STEEL TOP MOUNT WASTE CONTAINER

TOOLS REQUIRED:

45 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth and

wipe parts dry.

I-53TM-0317

3 4

11 12

Parts List

No. Description Qty

1 Metal Box 1

2 Lid 1

3 Slides 2

4 Slide Covers 2

5 Lid Holders 2

6 Door Mounting Brackets 2

7 Door Mounting Covers 2

8 Plugs 4

9 Waste Bins 2

10 #8x1/2” Pan Head Screws 12

11 #8x5/8” Flathead Screws 8

12 M4x5 Machine Screws 4

13 #6x1/2” Flathead Screws 6

14 1/4-28x1/2” Machine Screws 2

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 tnuom poT reniatnoc etsaw tnuom poT reniatnoc etsawTop 53TM SERIES STAINLESS STEEL TOP MOUNT WASTE CONTAINER tnuom poT tnuom poT tnnou oem pwoT r e n i a t c t s a TOOLS REQUIRED: reniatnoc etsaw reniatnoc etsaw wa 3 32 #2 tnuom poT reniatnoc etsaw T tnuom po etsaw reniatnoc #2 Parts List No.
PAGE 2
STEP 1 FIGURE 1 Using measurements in Figure 1, mark and pre-drill holes for lid holders and slides. Then attach each lid holder using (3) #8x1/2” pan head screws and each slide using (4) #8x5/8” flathead screws. 11/16” (17 mm) 18-11/16” (221 mm) 9-5/16” (237 mm) #2 22-1/4” (565 mm) 3 32 CABINET OPENING 19” (483 mm) 11-5/16” (287 mm) 1-1/2” (38 mm) 1-1/4” (32 mm) CABINET FLOOR FIGURE 2 STEP 2 tn reniatno Place the slide covers over the slides (See Fig 2).
PAGE 3
FIGURE 5 STEP 5 Mark and pre-drill mounting holes using measurements in figures 5 and 6. Attach door mounting brackets using (6) #6x1/2” flathead screws. 5/8” (16 mm) BETWEEN HOLES 1-7/8” (48 mm) 2-1/2” (64 mm) #2 3 32 14-11/16” (373 mm) + Door Overlay 13/16” (21 mm) + Door Overlay FIGURE 6 1) Make sure that your unit is securely installed into your cabinet. Remove the cabinet door and hinges to begin to mount your door.
PAGE 4
STEP 7 FIGURE 8 Adjust the door using the adjustment screws (See Fig 8) until the door is centered and flush with your frame. #2 VERTICAL ADJUSTMENT TILT ADJUSTMENT FIGURE 9 STEP 8 Place the door mount covers over the door mount brackets (See Fig 9). FIGURE 10 STEP 9 Place the lid on the holders and insert waste bins. (See Fig 10). 12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 4 Customer Service: 800-626-1126 | rev-a-shelf.
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.
PAGE 6
1 1 Usando las medidas en la figura 1, marque y pre taladre orificios para los sujetadores de la tapa y de los deslizantes. Luego, sujete cada sujetador de la tapa usando tres tornillos de cabeza de sartén del #8x1/2” y cada deslizante usando cuatro tornillos de cabeza plana del #8x5/8”. 11/16” (17 mm) 18-11/16” (221 mm) 9-5/16” (237 mm) En utilisant les mesures de l’Illustration 1, marquez et pré-percez les trous pour les supports de couvercle et les coulisses.
PAGE 7
5 5 Marque y pre taladre orificios de montaje usando las medidas en las figuras 5 y 6. Sujete los soportes de montaje usando seis tornillos de cabeza plana del #6x1/2”. Marquez et pré-percez les trous de montage en utilisant les mesures des Illustrations 5 et 6. Fixez les supports de montage de porte avec 6 vis à tête plate #6x1/2”.
PAGE 8
7 8 Ajuste la puerta usando los tornillos de ajuste (ver la figura 8) hasta que le puerta esté centrada y al ras con el marco. Réglez la porte avec les vis de réglage (voir l’Illustration 8) jusqu’à ce que la porte soit centrée et alignée avec votre cadre. AJUSTE VERTICAL RÉGLAGE VERTICAL AJUSTE DE LA INCLINACIÓN RÉGLAGE DE L’INCLINAISON 8 Coloque las cubiertas de montaje de la puerta sobre los soportes de montaje de la puerta (ver la figura 9).