Manualshelf

Template

ManualsBrandsRev-A-Shelf ManualsPull Out Trash Cans8-Quart Plastic Soft Close Pull Out Trash Can
12
Place template and mark hole
locations for the left hand slide.
Then attach each lid holder using
(3) #8x1/2” pan head screws
and each slide using (4) #8x5/8”
athead screws (See Figure 1).
Flip the template and do the same
for the right hand slide.
53TM SERIES STAINLESS STEEL TOP MOUNT WASTE CONTAINER
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
ESTIMATED ASSEMBLY TIME:
20 MIN
CARE AND MAINTENANCE:
CLEAN WITH A DAMP CLOTH
AND WIPE PARTS DRY
5
64
Top mount
waste container
Top mount
waste container
Top mount
waste container
Top mount
waste container
Top mount
waste container
Top mount
waste container
Top mount
waste container
Top mount
waste container
Top mount
waste container
3 4
6
21
7
10
5
8
9
11 12
Parts List
No. Description Qty
1 Metal Box 1
2 Lid 1
3 Slides 2
4 Slide Covers 2
5 Lid Holders 2
6 Door Mounting Brackets 2
7 Door Mounting Covers 2
8 Plugs 4
9 Waste Bins 2
10 #8x1/2” Pan Head Screws 12
11 #8x5/8” Flathead Screws 8
12 M4x5 Machine Screws 4
13 #6x1/2” Flathead Screws 6
14 1/4-28x1/2” Machine Screws 2
13
14
STEP 1
FIGURE 1
Place the slide covers over the
slides (See Fig 2).
STEP 2
FIGURE 2
Extend the slides and mount
the metal box using the (4)
M4x5 machine screws (See
Fig 3).
STEP 3
FIGURE 3
Place the (4) plugs over the
cylindrical screws (See Fig 4).
STEP 4
FIGURE 4
FIGURE 5
Mark and pre-drill mounting
holes using measurements in
gures 5 and 6. Attach door
mounting brackets using (6)
#6x1/2” athead screws.
STEP 5
B
+ Door
Overlay
1-7/8” (48 mm)
2-1/2” (64 mm)
5/8” (16 mm)
BETWEEN HOLES
13/16” (20 mm)
+ Door Overlay
Part Number B
53TM-1835GSCDM2-FL 10-7/8” (277 mm)
53TM-1850GSCDM2-FL 14-7/8” (378 mm)
53TM-18GSCDM3-FL 11-1/8” (282 mm)
53TM-24GSCDM4-FL 11-11/16” (297 mm)
1) Make sure that your unit is securely installed into your cabinet. Remove the cabinet door and
hinges to begin to mount your door.
2) Using the (4) provided screws and nuts, attach the L-Brackets to your slide.
Note: Depending on your particular basket design L-Bracket will mount on either inside or
outside of wire.
3a) Attach the door brackets to the outside of the L-brackets using the (4) provided screws.
Inside wire shown
4)
Aplique cinta de doble lado a los soportes de la puerta. Sujete la puerta del gabinete a los
soportes mientras trata de mantener la puerta a nivel. No se preocupe si la puerta se mueve un
poco, esto puede ser ajustado. La cinta de doble lado sujetara la puerta en su lugar mientras usted
atornilla los soportes a la puerta del gabinete.
Mettez du ruban adhésif double sur les supports de porte. Fixez la porte de l’armoire aux
supports tout en essayant de maintenir la porte à niveau. Ne vous inquiétez pas si elle n’est pas
tout à fait à niveau, tout cela peut être ajusté. Le ruban adhésif double tiendra la porte en place
pendant que vous vissez les supports sur la porte de l’armoire.
3c) Se proveen espaciadores de plástico si es que los soportes de la puerta necesitan ser extendi-
dos para alcanzar la porción gruesa de la puerta.
Des espaceurs en plastique sont fournis si les supports de porte doivent être étendus plus loin
pour atteindre la partie épaisse de la porte.
3b) Cada puerta de gabinete es diferente, pero asegúrese de que el soporte de la puerta se alinea
con la porción gruesa de la puerta del gabinete. Esto asegurará que los tornillos no se atraviesen ni
dañen su puerta.
Chaque porte d’armoire est diérente, mais assurez-vous que le support de porte s’aligne avec
la partie épaisse de la porte de l’armoire. Cela permettra d’assurer que les vis ne vont pas passer
à travers et endommager votre porte.
Measure Opening Height ________
Measure Door Height ________
Height Difference ________
Divide Difference by 2 ________ = Overlay
FIGURE 6
HOW TO DETERMINE YOUR DOOR OVERLAY:
FIGURE 7
Align the door brackets to the
slide covers and attach with (2)
1/4-28x1/2” machine screws
and washers (See Fig 7).
STEP 6
Adjust the door using the
adjustment screws (See Fig 8)
until the door is centered and
ush with your frame.
STEP 7
FIGURE 8
VERTICAL
ADJUSTMENT
TILT ADJUSTMENT
Place the door mount covers
over the door mount brackets
(See Fig 9).
STEP 8
Place the lid on the holders
and insert waste bins.
(See Fig 10).
STEP 9
FIGURE 10FIGURE 9
T-53TM-0619
WATCH TUTORIALS OF OUR
PRODUCTS BEING INSTALLED
WWW.REV-A-SHELF.COM/VIDEOS
TOOLS REQUIRED:
CABINET FLOOR
CABINET OPENING
CABINET REAR WALL
3-1/4”
(83 mm)
A
1-1/2” (38 mm)
1-1/4” (32 mm)
11/16”
(17 mm)
11-5/16”
(287 mm)
9-5/16”
(237 mm)
18-11/16”
(475 mm)
1-1/4”
(32 mm)
18-11/16”
(475mm)
11-5/16”
287mm
1-1/4”
32mm
1-1/4”
32mm
1-1/2”
38mm
9-5/16”
237mm
11/16”
17mm

Summary of content (2 pages)