Installation Instructions

ManualsBrandsRev-A-Shelf ManualsKitchen12 in. Pull-Out Baskets with Maple Solid Bottom

INSTALLATION INSTRUCTIONS: 5330/5386 SERIES PULLOUT BASKET WITH SOFT-CLOSE

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

5330/5386 SERIES PULLOUT BASKET WITH SOFT-CLOSE

TOOLS REQUIRED:

30 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth and

wipe parts dry.

I-53XX-0619

Parts List

No. Description Qty

1A Solid Bottom Basket 1

1B Solid Bottom U-Shaped Basket 1

2 Bottom Mount Brackets 4

3 Slides 2

4 Release Levers 2

5 Rear Slide Brackets 2

6 Side Mount Brackets 4

7 Mounting Brackets 2

8 Door Mounting Brackets 2

9 M4x6 Machine Screws 8

10 M4x10 Machine Screws 12

11 Euro Screws 4

12 1/4-20x1/2” Screws 4

13 #6x1/2” Flathead Screws 6

14 #6x3/4” Flathead Screws 4

15 #8x5/8” Truss Head Screws 8

1A)

1B)

2) 3)

FOR SIDE

MOUNTING

ONLY

FOR BOTTOM

MOUNTING ONLY

8) 9)

10)

11)

13)

WATCH TUTORIALS OF OUR

PRODUCTS BEING INSTALLED

WWW.REV-A-SHELF.COM/VIDEOS

FOR BOTTOM MOUNTING, PROCEED TO PAGE 2

FOR SIDE MOUNTING, PROCEED TO PAGE 3

14)

15)

12)

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 5330/5386 SERIES PULLOUT BASKET WITH SOFT-CLOSE TOOLS REQUIRED: 3 32 #2 3 mm ESTIMATED ASSEMBLY TIME: 1A) OR 1B) 30 MIN CARE AND MAINTENANCE: Clean with a damp cloth and wipe parts dry. 2) 3) 4) FOR BOTTOM MOUNTING ONLY 6) FOR SIDE MOUNTING ONLY 5) WATCH TUTORIALS OF OUR PRODUCTS BEING INSTALLED 7) 10) 8) 9) 11) 12) 13) WWW.REV-A-SHELF.COM/VIDEOS 14) 15) Parts List No.
PAGE 2
BOTTOM MOUNTING INSTRUCTIONS STEP 1 FIGURE 1 FIGURE 2 Attach bottom mount brackets to front and rear of each slide using (8) M4x10 screws (See Fig 1). STEP 2 FIGURE 3 Place template on cabinet floor and pre-drill hole locations (See Fig 2). 3 32 3 mm STEP 3 Attach slide to the floor using (4) #8x5/8” deep thread truss head screws on each slide (See Fig 3). FIGURE 4 Euro Screws (4) STEP 4 Install release levers and rear slide brackets to the bottom of the unit (See Fig 4).
PAGE 3
SIDE MOUNTING INSTRUCTIONS STEP 1 FIGURE 1 FIGURE 2 Attach the side mount brackets to the front of the slides using (4) M4x10 flathead screws (See Fig 1). STEP 2 Place side mounting template to side of cabinet and pre-drill hole locations (See Fig 2) and install the cabinet side mounting brackets. FIGURE 3 3 32 3 mm STEP 3 Place the slide assembly on top of the cabinet mounting bracket, insert (4) M4x10 flathead screws, adjust to the desired width of basket and tighten the screws.
PAGE 4
DOOR MOUNTING FIGURE 1 M4x6 Screws (4) FIGURE 2 STEP 1 Attach the mounting bracket to the tray with (2) M4x6 per side (See Fig 1). Insert (2) 1/4-20x1/2” screws into the mounting bracket per side, but do not completely tighten. 1/4-20x1/2” Screws (4) FIGURE 3 Insert door mounting bracket between screws and mounting bracket. Tighten the screws. Repeat for the opposite side (See Fig 2). NOTE: Door mounting bracket should face toward the outside of the bracket.
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.
PAGE 6
INSTRUCCIONES DE MONTAJE INFERIOR INSTRUCTIONS POUR LE MONTAGE PAR LE BAS 1 Sujete los soportes de montaje inferior al frente y a la parte posterior de cada deslizante usando ocho tornillos M4x10 (ver la figura 1). 1 2 Fixez les supports de montage par le bas à l’avant et à l’arrière de chaque coulisse avec 8 vis M4x10 (Voir l’Illustration 1). 2 Coloque la plantilla en el piso del gabinete y pre taladre orificios de ubicación (ver la figura 2).
PAGE 7
INSTRUCCIONES DE MONTAJE LATERAL INSTRUCTION POUR LE MONTAGE PAR LE CÔTÉ 1 Sujete los soportes de montaje lateral al frente de los deslizantes usando cuatro tornillos de cabeza plana M4x10 (ver la figura 1). 2 1 Fixez les supports de montage par le côté à l’avant des coulisses avec 4 vis M4x10 à tête plate (voir l’Illustration 1). 2 Coloque la plantilla de montaje lateral al lado del gabinete y pre taladre orificios de ubicación (ver la figura 2) e instale los soportes de montaje lateral del gabinete.
PAGE 8
MONTANDO LA PUERTA MONTAGE SUR LA PORTE 1 1 Sujete el soporte de montaje a la bandeja con dos tornillos de máquina de M4x6 por lado ( ver la figura 1). Tornillos de Máquina M4x6 / Vis Machine M4x6 Inserte dos tornillos del 1/4-20x1/2” dentro del soporte de montaje por lado, pero no los apriete completamente. Inserte el soporte de montaje de la puerta entre los tornillos y el soporte de montaje. Apriete los tornillos. Repita para el lado opuesto (ver la figura2).