Installation Guide
Installation Instructions
TANDEM plus BLUMOTION 562F
Cabinet & Drawer Specifications Drawer Size & Mounting Positions
Frame cabinet applications
Locking devices
Runner profiles
Rear mounting brackets (for frame applications)
All dimensions in millimeters. (Inch equivalents as noted)
Subject to technical modifications
without notice. Copyright 2009
For Frame and Panel cabinet applications
Preparing drawer for hardware installation
INST-TDM562FB.11.09
Subject to technical modifications
without notice. Copyright 2009
6 mm bit with
stop collar
2.5 mm bit with
extension chuck
Pilot boring for
locking devices
Boring rear holes
for runner hooks
75
°
Template
T65.1000.02
Universal drawer bracket set
• Includes (4) brackets
• Includes (8) M4 screws
295.4000
Rear bracket
Full extension concealed drawer runners
Important: Use of the T65.1000.02 template is recommended for accurate
location and angle of locking device pilot holes.
Locking device (right)
T51.1700.04R
Locking device (left)
T51.1700.04L
Rear mounting bracket, non-handed
295.3750.01
Installation screw (for locking devices and rear mounting brackets)
612TH
295.3750.01
612TH
Installation screw
T51.1700.04
Locking device
562F5330B
562F4570B
562F3810B
562F3050B
562F2290B
Runner
Overall
Cabinet
Depth
610
533
457
381
305
Interior Cabinet Depth
598
522
446
369
266
Maximum Minimum
Drawer
Length
533
457
381
305
229
(21")
(18")
(15")
(12")
(9")
Max.
Drawer
Thk.
Profile
Length
546
470
394
317
257
(23-9/16")
(20-9/16")
(17-9/16")
(14-9/16")
(10-15/32")
(24")
(21")
(18")
(15")
(12")
(21-1/2")
(18-1/2")
(15-1/2")
(12-1/2")
(10-1/8")
555
479
403
326
299
(21-7/8")
(18-7/8")
(15-7/8")
(12-7/8")
(11-13/16")
19
(3/4")
Installation screw (for mounting runner to cabinet side)
707N
612TH
Installation screw
19.5 (3/4")
30
(1-3/16")
Mounting Screw
M4 x 1/4"
NOTE: For frame applications.
Minimum 3 screws per bracket.
Bottom mount application
All dimensions in millimeters. (Inch equivalents as noted)
Subject to technical modifications
without notice. Copyright 2009
562H2290B Rear bracket, non-handed
295.3700.21
562H2290B Rear bracket, non-handed
295.3700.22
17.5 32
(1-1/4")
(11/16")
16 (5/8")
Face frame rail
Face frame stile
5 (3/16”)
4 (5/32”)
39.5 (1-9/16")
295.3700.2x
12
Face frame rail
Face frame stile
16 32
14 (9/16")
(1-1/4") (5/8") (3/32")
2
21
(13/16")
(15/32")
INDR 776.816.0 MA-192/1EN
NOTE: Because material thickness may vary, the inside drawer width must
equal interior cabinet width minus 50 (1-15/16") for TANDEM to align and
run properly.
13 (1/2")
7 (9/32")
Ø6 x 10
(1/4" x 3/8")
bore for hook
Use T65.1000.02
template for
accurate boring
11 (7/16")
33 (1-5/16")
For 19 mm (3/4") maximum
drawer side thickness
Bottom Clearance
14 (9/16")
Min. Top Clearance 6 (1/4")
Setback
4 (5/32")
Bracket Range
5 to 48
(3/16" to 1-7/8")
Drawer Gap
1 (1/32")
25 (31/32")
37 (1-7/16")
Target Drawer
Length
Drawer Thk.
Bottom Recess
13 (1/2")
Max. Drawer Height =
Opening minus
20 (13/16")
295.3750.01
Rear Mount Bracket
Mounting Screws
612TH
(#6 x 1/2" Truss Head)
Mounting Position 10 (3/8")
Overall Cabinet Depth
Interior Cabinet Depth
Profile Length
Drawer Length
Drawer removal and installation
Height adjustment
1. Squeeze orange handles on
locking devices
2. Pull drawer straight out and up
1. Place drawer on runners and
close, locking devices will
automatically connect to runners
1. Press up on adjustment tab.
2. Push towards back of drawer.
Max. 3mm (1/8") rise of drawer.
Tilt adjustment
Formula for calculating outside drawer width
For drawer side
thickness
19
(3/4")
18
(23/32")
17
(21/32")
16
(5/8")
15
(19/32")
Deduct from inside
cabinet width
11
(7/16")
13
(15/32")
14
(9/16")
17
(21/32")
19
(3/4")
for 2290B only
Min. top
clearance
6 (1/4")
Inside cabinet width
Drawer width
Opening
13 (1/2")
Bottom recess
Drawer side thickness
maximum 19 (3/4")
14 (9/16")
Bottom clearance
3 7
(1-7/ 1 6")
25 (31/32")
Drawer height
maximum =
opening minus
20 (13/16")
System or
#7 profile
mounting
screws
Rotate the tilt adjustment lever on the
rear of each runner profile to tilt the top
of the drawer front forward.
Tool free tilt adjustment
+
5 mm.