Assembly Instructions

12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
BLUM VANITY BOTTOM MOUNT TEMPLATE
TOOLS REQUIRED:
30 MIN
ESTIMATED ASSEMBLY TIME:
CARE AND MAINTENANCE:
Clean with a damp cloth and
wipe parts dry.
PARTS LIST
- Frame/slide assembly
- Hamper basket
- (6) #6 x1/2” at head screws
- (4) #8 x3/4” deep thread pan
head screws
- (4) #6 x 1/2” deep thread pan
head screws
- Template
1
16
1.
3.
FIGURE 2
FIG. 1
1) ATTACH BUT DO NOT
TIGHTEN USING
#6 X 1/2” FLAT HEAD
SCREWS
3) PRE-DRILL AND
ATTACH
4) TIGHTEN SCREWS
2) ADJUST DOOR
TO BE CENTERED
IN CABINET
HORIZONTALLY
1) Make sure that your unit is securely installed into your cabinet. Remove the cabinet door and
hinges to begin to mount your door.
2) Using the (4) provided screws and nuts, attach the L-Brackets to your slide.
Note: Depending on your particular basket design L-Bracket will mount on either inside or
outside of wire.
3a) Attach the door brackets to the outside of the L-brackets using the (4) provided screws.
Inside wire shown
4)
Aplique cinta de doble lado a los soportes de la puerta. Sujete la puerta del gabinete a los
soportes mientras trata de mantener la puerta a nivel. No se preocupe si la puerta se mueve un
poco, esto puede ser ajustado. La cinta de doble lado sujetara la puerta en su lugar mientras usted
atornilla los soportes a la puerta del gabinete.
Mettez du ruban adhésif double sur les supports de porte. Fixez la porte de l’armoire aux
supports tout en essayant de maintenir la porte à niveau. Ne vous inquiétez pas si elle nest pas
tout à fait à niveau, tout cela peut être ajusté. Le ruban adhésif double tiendra la porte en place
pendant que vous vissez les supports sur la porte de l’armoire.
3c) Se proveen espaciadores de plástico si es que los soportes de la puerta necesitan ser extendi-
dos para alcanzar la porción gruesa de la puerta.
Des espaceurs en plastique sont fournis si les supports de porte doivent être étendus plus loin
pour atteindre la partie épaisse de la porte.
3b) Cada puerta de gabinete es diferente, pero asegúrese de que el soporte de la puerta se alinea
con la porción gruesa de la puerta del gabinete. Esto asegurará que los tornillos no se atraviesen ni
dañen su puerta.
Chaque porte d’armoire est diérente, mais assurez-vous que le support de porte saligne avec
la partie épaisse de la porte de l’armoire. Cela permettra d’assurer que les vis ne vont pas passer
à travers et endommager votre porte.
Measure Opening Height ________
Measure Door Height ________
Height Difference ________
Divide Difference by 2 ________
Mark screw locations on your
door and pre-drill.
Note:Be careful not to drill
through the cabinet door.
Measure from frame to top bracket slot ________
Measure from frame to bottom bracket slot ________
2.
Refer to (Fig. 1) for the proper door mounting
measurements.
Once you have the measurements required to
mount the frame to your door correctly, pull out
the frame and attach the brackets to the door
with the provided (6) #6 x 1/2” screws (See Fig. 2).
DO NOT TIGHTEN THE SCREWS ALL THE
WAY AT THIS TIME.
Close the frame and adjust your door to center
to your cabinet opening. Slowly pull the frame
out of the cabinet and tighten your door
mounting screws. Pre-drill one of the center
holes on both sides of the door mount brackets
and install another door mounting screw to keep
the door centered.
If your door is larger than the
cabinet opening, add the divided
difference you found in step 2 to the
measurements in step 1. If your door is
smaller, subtract the divided difference
from the measurements in step 1.
Top Measurement ________
Bottom Measurement ________
DOOR MOUNTING
T-4WHVCSC-0417
1
16
INSTALLING THE SLIDE SET
1. Measure the cabinet opening and mark the centerline.
2. Align this template with your marked cabinet centerline and
tape in place.
NOTE:Youmayhavetofoldorcuttemplatetotitincabinet.
a. Inset Door – Set this template back in the cabinet the width of
the face frame.
b. Overlay – Place the front edge of the template to the front
edge of the cabinet.
3. Use an awl and mallet or a pencil to mark the cabinet oor at
the 4 screw locations (denoted by solid dots on the template)
and remove template.
4. Lay your slide assembly in the cabinet, aligning the holes to the
marks from step 3 and attach using the (4) #8 x 3/4” deep thread
screws starting with the back holes rst.
NOTE:Pullslidesforwardforbetteraccesstobackholelocations.
1. Turn frame upside down.
2. Place Blum triggers to the front and side walls of frame, aligning to
predrilled holes.
NOTE:Theorangecoveroftriggerfacestheinsideoftheframe.
3. Attach triggers to frame using (4) #6 x 1/2” deep thread pan head
screws.
4. Place the frame onto the slide assembly and push back until the unit
locks to slides. NOTE:Youwillheara“click”whenitlocks.
5. Loosen screws on side of door mount brackets. Remove brackets and
switch sides so brackets face outside and retighten.
a. For inset door, leave brackets facing inside.
FRAME PREPARATION
CENTER LINECENTER LINE
FRONT EDGE OF PAPER
TO FRONT OF EDGE OF
CABINET OPENING OR
FRONT OF FACE FRAME.
IF INSTALLING IN INSET
DOOR APPLICATION,
MOVE TEMPLATE BACK
THE THICKNESS OF THE
DOOR.

Summary of content (2 pages)