Instructions / Assembly

Customer Service: 800-626-1126 | rev-a-shelf.com
8
Attach the telescopic foot to the
lower stud mount using the #8-32 x
1/2” machine screws and at washers
provided, making sure not to tighten
at this time (See Fig 1). Lay ush to the
oor of the cabinet. Once the foot is in
full contact with the oor of the cabinet,
tighten the machine screws from the
previous step. Now attach the foot to
the oor of the cabinet using (2) #8
x 5/8 deep thread screws provided.
Make sure the foot and stud mount
are perpendicular to the oor of the
cabinet and do not lean left or right
(this will cause interference with the
gas spring that operates the waste
container).
FINALIZING INSTALLATION OF
THE FRAME IN THE CABINET
STEP 1
ATTACHING THE DOOR
STEP 2
Use separate door mount worksheet to
attach product to door.
During the rst 5-10 cycles extend the
frame to the fully open and fully closed
positions assisting the entire length of
travel. At this point the unit should open/
close itself for the last 6-8” of travel.
NOTE: If the unit is not opening/closing
fully or not operating smoothly check
the following:
-Make sure that the installation of the
front and rear brackets allow the slides
to be “square” without binding by
measuring corner to corner on the slides
with the unit in the open position.
-Check that the slides are both level front
to back and that they are also level from
one slide to the next (laying a level across
both slides when waste container is in the
open position).
-Check that the bottom foot is vertical
front to back and left to right.
TESTING FUNCTIONALITY
STEP 3
#2
FIGURE 1
Step 6
Re-engage the unit into each of the cabinet members being sure that the slides are
aligned properly. Once engaged fully close and open the unit a few times to ensure
proper slide operation.
Step 7
Re-install the gas spring being sure that the gas reservoir is attached to the top stud
as shown in Figure 7A. Make sure to install both of the retainer clips into each of the
stud caps.
Step 8
Attach the telescopic foot to the lower stud mount using the #8-32 X 1/2” machine
screws and at washers provided (do not fully tighten). The stud mount is threaded so
there is no need to use a nut and the foot itself is slotted. Once you are sure the foot
is in full contact with the oor of the cabinet, tighten the machine screws. Now that
the foot is the correct length attach it to the oor of the cabinet using (2) #8 x 5/8 deep
thread screws provided. Make sure the foot and stud mount are perpendicular to the
oor of the cabinet and do not lean left or right (this will cause interference with the
gas spring that operates the waste container). (SEE FIGURE 8A)
Step 9
Attach door to unit.
(SEE ENCLOSED DOOR MOUNTING INSTRUCTION SHEET)
FIGURE 7A
FIGURE 8A
12400 Earl Jones Way • Louisville, KY 40299
800-626-1126
www.rev-a-shelf.com
I-WCTMSC-0115
Step 10 Test Function
Once the door has been properly attached test the function of the unit. During the rst 5-10 cycles extend the frame to the
fully open and fully closed positions assisting the entire length of travel. At this point the unit should open/close itself for
the last 6-8” of travel.
NOTE: If the unit is not opening/closing fully or not operating smoothly check the following:
-Make sure that the installation of the front and rear brackets allows for the slides to be “square” without binding by mea-
suring corner to corner on the slides with the unit in the open position .
-Check that the slides are both level front to back and that they are also level from one slide to the next (laying a level
across both slides when waste container is in the open position).
-Check that the bottom foot is vertical front to back and left to right.
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126