Installation Instructions

2
BY DATE
DRAWN
DRAWING NO. SCALE
MATERIAL
FINISH
PART NO. SHEET OF
This drawing is the property of Rev-A-Shelf (RAS) and is disclosed
in confidence to the extent its subject matter is original to RAS. Any
vendor receiving this drawing from RAS shall hold and use this drawing
for the sole benefit of RAS and shall not disclose it to, or use or
reproduce it for any third party, or perform any act adverse to the interest
of RAS with respect to this drawing without the express written permission
of RAS. Vendors shall not revise any physical, dimensional or
performance characteristic unless authorized by Rev-A-Shelf Engineering.
TOLERANCES
MAT. DEC. ANGLES
(WOOD) .XX .03 [.8mm] 1/2
(OTHER) .XX .02 [.5mm]
(ALL) .XXX .005 [.13 mm]
FRACTIONS 1/32 [.8 mm]
SIZE
B
INCH
[MM]
AMERICAN
PROJECTION
1 2
CUSTOMER DRAWING
20.97
[532,64]
19.62
[498,3]
9.82
[249,3]
5.00
[127]
23.00
[584,3]
21.63
[549,3]
20.25
[514,4]
21.87
[555,6]
REV. DATE BY DESCRIPTION OF CHANGE
DOUBLE 30 QUART WASTE
CONTAINER BLUM SOFT CLOSE
BKT 7/30/15
0.100 4WCSC-2430DM-2
4WCSC-2430DM-2
Customer Service: 800-626-1126 | rev-a-shelf.com
STEP 2
STEP 3
Remove the slide triggers from their
wrapping.
Turn your waste container chassis
over and locate the pre-drilled holes
on the front lip of the box
(See Figure 2A).
Using (4) #6 x 1/2” deep thread pan
head screws, attach the left and
right sided triggers (See Figure 2B)
and set the waste container chassis
to the side.
NOTE:
Release triggers are side sensitive
and are marked with an “L” & “R”
for Left and Right.
Place template into cabinet and
position thefront edge to where
the back of your door will be when
closed (See Figure 3).
Inset door = set back the thickness
of your door
Overlay door = place at the front
edge of cabinet
Using an awl or pencil, mark
through the bold dotted screw
locations onto your cabinet oor.
Remove template when done.
Using your 3/32” drill bit, pre-drill
in all 8 locations making sure to
NOT drill through the cabinet oor
completely.
Lay your assembled slide set over
the top of the marked holes. Using
(8) #6 X 1” deep thread Phillips
head screws, attach the slides to
the cabinet oor through the gray
slide feet holes.
Place your waste container chassis
with attached triggers on top of the
slides and push back until you hear
the “click” sound.
To assemble the slides, attach the
cross bar into the feet
(See Figure 1A).
Attach the left and right slides
respectively to the top of the
feet. You will feel a “snap”when
connected completely
(See Figure 1B).
Once slides are assembled, set
them to the side.
STEP 1
#2
FIG. 1A FIG. 1B
Pre-drilled holes
Slide triggers
FIG. 3
FIG. 2BFIG. 2A
#2
3
32
Edge of paper to
back of door
Center line of
cabinet opening
Fold here to t Cabinet
1) Place template into cabinet and position front edge to where the back of
your door will be
a. Inset door = set back the thickness of your door
b. Overlay = place at the front edge of cabinet
2) Using an awl or pencil, mark through the bold dotted screw locations onto
your cabinet oor. Remove template when done
3) Lay your assembled slide set over the top of the marked holes and using the
provided 8 screws, attach the slides to the cabinet oor through the grey
slide feet holes
4) Place your Waste Container chassis with attached triggers on top of the
slides and push back until you hear the “click” sound. You are now ready to
insert the waste receptacles into the chassis.
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
DOUBLE 30QT WASTE CONTAINER W/ BLUM SOFT-CLOSE TEMPLATE
T-4WCBM2430SC-TRI-0116
Note: The ideal distance
between bracket
screws should be
21-5/8”, allowing
for maximum
adjustability.
23“
21-5/8“
21-1/4“
9-13/16“
5“