Installation Instructions

ManualsBrandsRev-A-Shelf ManualsKitchen19.62 in. H x 21 in. W x 21.875 in. D Double Pull-Out Bottom Mount Wood and Silver Waste Containers with Soft-Close

INSTALLATION INSTRUCTIONS: DOUBLE 30 QT WASTE CONTAINER WITH BLUM SOFT-CLOSE

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

4WC DOUBLE 30 QT WASTE CONTAINER WITH BLUM

SOFT-CLOSE

TOOLS REQUIRED:

20 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth and

wipe parts dry.

I-4WC-24DM2-SC-0519

No. Description Qty.

A Waste Container Chassis 1

B #6 X 1/2” Pan Head Deep Thread Screws 4

C #6 X 1” Deep Thread Phillips Head Screws 8

D 30 qt Waste Containers 2

E #6 X 1/2” Flat Head Screw 5

F Double Sided Tape 4

G Spacer Kit 1

H Slide Straps 2

I Slide Strap Feet 2

J Left & Right Slides 2

K Left and Right Slide Triggers 2

Parts List

B. F.A.

J. K.

C. D.

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 4WC DOUBLE 30 QT WASTE CONTAINER WITH BLUM® SOFT-CLOSE TOOLS REQUIRED: #2 3 32 Parts List No. Description Qty. A Waste Container Chassis 1 B #6 X 1/2” Pan Head Deep Thread Screws 4 C #6 X 1” Deep Thread Phillips Head Screws 8 D 30 qt Waste Containers 2 E #6 X 1/2” Flat Head Screw 5 F Double Sided Tape 4 CARE AND MAINTENANCE: G Spacer Kit 1 Clean with a damp cloth and wipe parts dry.
PAGE 2
STEP 1 To assemble the slides, attach the cross bar into the feet (See Figure 1A). FIG. 1A FIG. 1B Attach the left and right slides respectively to the top of the feet. You will feel a “snap”when connected completely (See Figure 1B). Once slides are assembled, set them to the side. STEP 2 Remove the slide triggers from their wrapping. Turn your waste container chassis over and locate the pre-drilled holes on the front lip of the box (See Figure 2A). FIG. 2A FIG.
PAGE 3
STEP 4 Re-install door mount brackets. FIG. 4 NOTE: Spacers may be needed in between the upright and door mount bracket to reach the thick portion of the door (See Figure 4). DOOR MOUNT INSTALLATION STEP 5 Refer to Figure 5 to determine door mounting hole locations. Transfer these dimensions to your door from the bottom and mark the hole locations. Pre-drill these holes on the back side of your cabinet door, making sure NOT to drill through the door. FIG.
PAGE 4
DOOR MOUNT WITH DOUBLE SIDED TAPE STEP 7 FIG. 7 Apply double stick tape to the door brackets. Attach cabinet door to the brackets while trying to keep door level. Don’t worry if it is off a little. This can all be adjusted. Double stick tape will hold the door in place while you screw the brackets to cabinet door (See Figure 7).
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.
PAGE 6
PASO 1 / ÉTAPE 1 Para montar los deslizantes, coloque la barra transversal en la base (Ver Figura 1A). Coloque los deslizantes izquierdo y derecho , respectivamente, en la parte superior de la base. Escucharás un “chasquido” cuando esté completamente conectado (Ver Figura 1B). Una vez que los deslizantes estén montados, colóquelos a un lado. FIG. 1A FIG. 1B Pour assembler les glissières, fixez la barre transversale dans les pieds (voir fig. 1A).
PAGE 7
PASO 4 / ÉTAPE 4 FIG. 4 Vuelva a instalar los soportes de montaje de la puerta. NOTA: Es posible que se necesiten espaciadores entre el soporte vertical y el soporte de montaje de la puerta para alcanzar la parte gruesa de la puerta (consulte la Figura 4). Réinstallez les supports de montage de porte. REMARQUE : des entretoises peuvent être nécessaires entre le montant et le support de montage pour atteindre la partie épaisse de la porte (voir fig. 4).
PAGE 8
MONTAJE DE PUERTA CONCINTA DE DOS LADOS MONTAGE SUR PORTE AVEC BANDE ADHÉSIVE DOUBLE-FACE PASO 7 / ÉTAPE 7 Ponga la cinta de dos lados en los soportes de la puerta. Fije la puerta del gabinete a los soportes mientras trata de mantener el nivel de la puerta. No te preocupes si está un poco desajustado. Todo esto puede ser ajustado. La cinta de dos lados mantendrá la puerta en su lugar mientras atornilla los soportes a la puerta del gabinete (consulte la Figura 7).