Installation

448 Ball-Bearing Soft-Close Wall
Cabinet Pullout Installation
Template - 5” Version
Cut at this line to t
template in your cabinet
T-448BBSCWC-1116
PARTS LIST:
WOOD FRAME W/ ATTACHED SLIDE
DOOR MOUNT BRACKETS
SHELVES
ESTIMATED ASSEMBLY
TIME:
3045 MIN
CARE AND MAINTENANCE:
CLEAN WITH A DAMP CLOTH
AND WIPE PARTS DRY
Edge front of template
to back of cabinet door.
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
Center of Cabinet
Pre-Drill for
bolt application
Pre-Drill for
bolt application
Pre-Drill for wood
screw application
Pre-Drill for wood
screw application
STEP 1
Proceed to the door mounting section.
Place your 448 unit over the top of your holes and
secure using the 4 machine bolts. Make sure the
bolts go through the holes from the underside of
the cabinet up into the cabinet oor, and secure
with a 1/4” nut driver or wrench. The corresponding
holes on the slide set are threaded for attachment.
Using your 3/8” drill bit, drill through the 4 marked
hole locations labeled “Pre-drill here for bolt
application.” You will drill through your cabinet oor.
Place Template inside of your wall cabinet. Orientate
the template so the front edge is positioned to the
back of your cabinet door (See Fig 2).
Place Template inside of your wall cabinet. Orientate
the template so the front edge is positioned to the
back of your cabinet door (See Fig 2).
Using your awl and rubber mallet, punch your hole
locations identied by the smaller black circles
(See Fig 2).
Re-attach the wood frame to your slides. Be sure
your ball bearing race tracks have been placed at
the front of your slide channels. Align the wood
frame & push to the closed position. Proceed to the
door mounting section at this time.
Secure slide set to cabinet oor using the 4 wood
screws provided.
SEE BELOW FOR ILLUSTRATIONS
Measure from the base of the face frame up to each
mounting bracket slotted hole location and record
those dimensions.
Measure the entire door opening and record that
value. Measure the height of your cabinet door and
record that value.
Transfer these dimensions to your door from the
bottom and mark the hole locations.
Pre-drill these holes on the back side of your cabinet
door, keeping sure not to drill through the door.
STEP 2
STEP 1
STEP 4
STEP 5
STEP 6
STEP 3
STEP 2
STEP 4
STEP 1
DETERMINING YOUR INSTALLATION
INSTALLATION WITH BOLTS
DOOR MOUNTING INSTRUCTIONS
If you plan to secure your 448 organizer using the
provided bolts, please proceed to the “Installation
with bolts” section. If you plan to secure using wood
screws (See Fig 1.1), proceed to the “Installation
with wood screws” section.
Turn your 448 upside down. Pull your SC slide set
into the open position and locate the triggers on
the left and right side (See Fig 1.2). Press and hold
the triggers either up or down while also removing
the slide set. Set your wood frame to the side for
now. After you remove the slides, your soft-close
mechanism will be in the open position. Flick the
trigger and reset it to the closed position.
FIGURE 1.1 FIGURE 1.2
FIGURE 2
SLIDE RELEASE LOCATION
WOOD SCREWS FROM
TOP OF SLIDE ASSEMBLY
(4 TOTAL)
INSTALLATION WITH WOOD SCREWS
Measure Opening Height (a)________
Measure Door Height (b)________
Mark screw
locations on
your door and
pre-drill. Be
careful not to
drill through the
cabinet door.
If your door is larger than cabinet opening, add the divided
difference you found in step 2 to the measurements in step 1.
If your door is smaller, subtract the divided difference from the
measurements in step 1.
Top bracket Measurements
Right________ Left________
Bottom bracket Measurements
Right________ Left________
Measure from frame to left bracket slot ________
Measure from frame to right bracket slot ________
(repeat step for top brackets)
1.
2.
3.
(a) (b)
3
32
Height Difference ________
Divide Difference by 2 _______
TOOLS REQUIRED:
3
8
3
8
4