IQBoard ET & PS User Manual Copyright(C) 2003-2010 Fuzhou Returnstar Technology Co.,Ltd. Web: www.recoverystar.com; www.iqboard.net Tel: 0086-591-87274373 Fax: 0086-591-87274383 E-mail: master@recoverystar.
Important Statements This manual is for IQBoard ET and IQBoard PS. The “Whiteboard” or “Interactive Whiteboard” in this manual all refer to IQBoard ET or IQBoard PS. The “Electronic Pen” and “Electronic Pointer” are used for IQBoard ET. The “Colorless Writing Pen (Finger)” is used for IQBoard PS. Use this product strictly according to detailed operation instruction in this manual so as to ensure proper use. Before you install this product, please read this manual carefully to save your time.
Chapter 1 Product Introduction IQBoard ET and IQBoard PS are the latest interactive presentation boards. Connect IQBoard ET or PS with your computer and projector, then simply touch the projection area with electronic pen or your finger, you can transform the electronic pen or your finger to mouse and directly operate the computer on the projection area. The difference between IQBoard ET and PS are IQBoard ET adopts electronic pen for operation, and while IQBoard PS can be directly operated by your finger.
Chapter 2 Specification Performance: Effective resolution: 9600×9600, 300dpi; Signal tracking rate: 3m/s; Processing rate for writing or clicking: 240 dot/s. Provide 9 or 20 points precise orientation. Power consumption for electronic pen: ≤1.5 W. IQBoard ET provides sizes of 80 inches, 60 inches, 50 inches (4:3), 100 inches, 120 inches (16:9) and customized sizes. IQBoard PS provides sizes of 80 inches, 60 inches (4:3), 100 inches, 112 inches (16:9) and customized sizes.
IQBoard ET&PS Models System Requirement Windows XP/2003/Vista operation system Pentium166 CPU (PentiumII or higher recommended) 64 MB RAM (128 MB recommended) 1G free hard disk space (for full installation) 1 free USB port 1 projector (short focus or ultra-short focus projector recommended)
Chapter 3 Install IQBoard 3.1 Mount Whiteboard 3.1.1 For product with an “M” on its name In case your product having an “M” on its name, you can select wall mounting. Parts list: Picture Name Quantity Screw 4 Wall Anchor 2 Safety Bracket 2 Anchor Bolt 2 Wall Mounting Bar 1 Wall Mounting Bracket (already mounted on 2 the backboard) Installation Steps: Step 1. Determine the installation height of the Wall Mounting Bar (190cm above floor), then fasten bracket to wall using the two Anchor Bolts.
Note: When mounting the Wall Mounting Bar, mind its direction. Step 2. Align the 2 Wall Mounting Brackets on the backboard with the Wall Mounting Bar, and hang the whiteboard on the wall. Step 3. Fasten the 2 Safety Brackets on each side of whiteboard lower frame using 2 Screws. According to the location of the Safety Brackets, drill 2 mounting holes on the wall. Finally use Wall Anchors and Screws to fix the Safety Brackets on the wall. 3.1.
Screw Wall Anchor 4 2 2 Safety Bracket 4 Anchor Bolt Height Adjust Bracket (already 4 mounted on backboard) Installation Steps: Step 1. Drill 4 holes at the location where you want to place the 4 Anchor Bolts, insert the 4 Anchor Bolts in these holes, and leave 4mm clearance between bolt head and nut for hanging whiteboard.
Prompt: The distance from floor to the 2 anchor bolts on top (Distance X) is 190cm. The vertical distance between 2 anchor bolts (Distance H) is 45cm for the 50" and 60" whiteboards, and 75cm for the 80", 100", 112", and 120" whiteboards. For the horizontal distance between 2 anchor bolts (Distance L), please measure horizontal distance of the 2 Height Adjust Brackets on the backboard. Step 2.
Picture Name Quantity Leg Bar 2 Column 2 Supporting Bar 2 Caster 4 Moveable Crossbeam (Each includes 2 Beams and a U-Shaped Groove) 2 Hexagon Bolt A 2 Hexagon Bolt B (M8 × 50, with 08/22 washer) 4 Hexagon Bolt C (M8×50) 8
Hexagon Bolt Set A (M8× 50) 6 Hexagon Bolt Set B (M8× 35) 4 Anchor Bolt (M8×60) 4 Wrench 1 Each set includes: 1 Hexagon Bolt, 1 Wind Nut, 1 M8 Nut, 1 Small Washer, 1 Big Washer Each set includes: 1 Hexagon Bolt, 1 Wind Nut, 1 Small Washer, 1 Big Washer Installation Steps: Step 1. Install Column on each Leg Bar using Hexagon Bolt B. Step 2. Install one end of each Supporting Bar on each Leg Bar, using Hexagon Bolt A.
Step 3. Install the other end of each Supporting Bar on each Leg Bar, using Hexagon Bolt Set A. In this stage, please partially screw the bolt, leaving 4mm clearance between bolt head and column for hanging whiteboard. Step 4. Install 2 Casters on each Leg Bar. Step 5.
Step 6. Laid down and connect the two leg assemblies with the U-Shaped Grooves. Step 7. Secure the U-Shaped Grooves with Hexagon Bolt Set B. In this stage, do not completely tighten the bolt in order to adjust the stand width later.
Step 8. Install 2 Hexagon Bolt Sets A on each Column, leaving 4mm clearance between bolt head and nut for hanging whiteboard. Step 9. Align the Hexagon Bolt on the Column with the clip holes of Height Adjusting Bracket on backboard, and hang the one side of whiteboard on the stand. Then adjust the stand width to fit the whiteboard, and hang other side of the whiteboard on the stand. Finally, tighten the bolts on the U-Shaped Groove and Columns. on Hexagon Bolts.
Prompt 1. You can use different clip holes of the Height Adjusting Bracket to adjust the whiteboard height. Generally the bottom of the whiteboard should be 70-80cm above the ground. 2. For 50 and 60 inch whiteboard, you can hang the whiteboard on the first and second bolts from top down on the Column. For 80, 100, 112, and 120 inch whiteboard, you can hang the whiteboard on the first and third bolts from top down on the Column. Fully assembled whiteboard is as follows: 3.
3. Screw the battery cap back by turning it clockwise 3.3 Replace Pen Tip of Electronic Pen 1. Unscrew the pen tip cap by turning it counterclockwise. 2. Replace the pen tip by inserting its concave end into the pen body. 3. Screw the pen tip cap back by turning it clockwise. 3.4 Install Battery of Electronic Pointer 1. Gently lift the battery cover to open it. Prompt: Please gently open the battery cover to avoid damaging the connecting line. 2. Insert 1 AAA battery with the plus (+) side up. 3.
Chapter 4 Connect IQBoard to Computer After fixing the whiteboard, find a connecting port on the backboard right bottom. Plug the quadrate side of USB cable into the connecting port, and plug the flat side into the available USB port of computer, as follows. External power source is not required. And please connect the Projector into the VGA port of your PC video card.
Maximum projection area for whiteboards without hotkey or with hard hotkeys Maximum projection area whiteboards with soft hotkeys for The blue areas are the maximum projection areas. For whiteboards without hotkey or with hard hotkeys, there should be 2cm margin between projection area and whiteboard inner frame. For whiteboards with soft hotkeys, the projection area should not exceed the hotkeys. Note: 1. In case you use 16:9 whiteboard, please choose the projector supporting the 16:9 projection mode.
Chapter 5 Install and Uninstall Drivers 5.1 Install Drivers Run “IQBoard ET & PS Drivers.exe” in the installation CD, and install the drivers according to the prompt. The computer will automatically find a new hardware and install the drivers. After the installation is completed, if the indicator beside the USB connecting port turns green, the whiteboard can be used normally. If the indicator turns red, it means the USB cable is not well connected, please re-connect the USB cable or restart computer.
Chapter 6 Setup IQBoard 6.1 Orient IQBoard At the first time you use the whiteboard, you need to orient it, so the moving track of the electronic pen or writing pen (finger) can match the cursor. You can select 4 points, 9 points or 20 points orientation. Normally 9 points orientation is adopted. After the whiteboard is oriented, you don’t need to re-orient at the same environment. To orient the whiteboard 1.
3. Do one of the followings: If you use pen or finger, follow the on-screen instructions, press the center of each cross accurately with pen tip or finger tip. If you use electronic pointer, follow the on-screen instructions, press the center of each cross accurately with pointer tip and press the button on the pointer body. Your whiteboard is now oriented. Prompt: 1.
Prompt: 1. When setting the soft hotkeys, if some error occurs, you can press “ESC” key on the keyboard to exit the setting process, and then reset the hotkeys. 2. You don’t need to set the hard hotkeys. 6.3 Enable Handwriting Recognition Touch Recognition allow the whiteboard to sense the difference between a pen, finger and palm of the hand. You can write and draw with the pen, move objects with your finger, and erase with the palm of your hand all at the same time -- no tool switching required.
To enable Touch Recognition function 1. Select “Start > Programs > IQBoard ET & PS Drivers >Touch Recognition Setting”. 2. Select the Enable Touch Recognition of IQBoard PS V7.0 check box. After you enable the Touch Recognition, you can use this function. When using this function, if the whiteboard often misinterprets your intent, you can customize Touch Recognition's sensitivity to suit your style. Before set up touch recognition function, please specify the whiteboard size.
Chapter 7 Use IQBoard 7.1 Basic Operations For IQBoard PS, you can use the enclosed writing pen or your finger to write or perform mouse function. For IQBoard ET, you can use the enclosed electronic pen or electronic pointer to operate. Following are the tips for some basic operations: Single-click If you use pen or finger, press the surface with pen tip or finger tip at proper strength.
If you use pen or finger, start IQBoard Software, select a drawing tool, then you can write or draw by pressing the surface with pen tip or finger tip. If you use electronic pointer, start IQBoard Software, select a drawing tool, then you can write or draw by pressing the surface with pointer tip, and pressing and holding the button on the pointer body. 7.2 Use Touch Recognition Once you have enabled Touch Recognition, you can use this convenient function to write, select object, and erase content.
The electronic pen of IQBoard ET has 2 multi-functional interactive buttons. You can achieve dozens of functions by simply pressing the interactive buttons. Following are the operations of these interactive buttons. When using these buttons, please touch the whiteboard surface gently with pen tip. Do not press the surface. When in Windows Mode Front Button: Press the button once to execute left-click function. Back Button: Press the button once to execute right-click function.
Prompt: 1. To know the details of the above mentioned modes and status, please refer to IQBoard Software user manual. 2. When you press the Back Button to select a Freehand Drawing Tool or an Eraser, the default Free Hand Drawing tool is Pencil, and the default Eraser is Normal Eraser. If you have selected other Freehand Drawing Tool or Eraser before, IQBoard Software will use your previous selections. 7.4 Use Hotkeys on whiteboard Following is the introduction of these hotkeys.
: Press this key to go to the next page. Next Page Mouse : Press this key, you can use electronic pen or writing pen (finger) to achieve click, double-click, and drag function. When using IQBoard Software, press this key to switch between “Windows” and “Board” mode. Pen: There are four “Pen” keys in different colors on the hotkey bar. Press one of these keys, you can write on board in corresponding color. Press “Pen” twice to modify its properties.
Chapter 8 FAQ 1. The whiteboard indicator is not lighting or turns red. The hotkey is not functioning. 1. The USB cable is not well connected with whiteboard or computer, please check and re-connect. 2. The USB port is damaged, please try another one. In case you are using desktop computer, please use its rear USB port. 3.
you touch the screen with pen or finger, and will be separated again when you lift the pen or finger. But if continuous force is exerted on one area, the front layer and back layer may stuck together, leave a constant sensing point. 4. When operating and writing on the whiteboard, the position of pen or finger doesn’t match the position of cursor. 1. The relevant location of projector and white has been changed. Please re-orient the whiteboard. 2.
Background knowledge: IQBoard ET adopts working principle of electromagnetic induction. So if there is interference source that can generate strong magnetic field nearby, the above symptom will occur. In normal condition, devices like cell phone, display, TV won’t affect IQBoard ET. In case the interfering magnetic field is too strong, you can move either the interference source or IQBoard ET to keep their distance over 50cm. 8. The pen tip worn out. Common abrasion will not affect normal operation.
Chapter 9 Cautions and Maintenance 9.1 Whiteboard For the interactive whiteboard that do not support normal marker (the product model is without “W”), please try not to use normal marker to write on the surface. Before cleaning, please shut down the computer and switch the projector into standby mode to make the dirt more obvious. In case of normal dirt, spay some water or detergent on the surface, then use the paper to wipe the dirt out.
6. To avoid harm from improper operation, please do not use chair or other tool to help short students use the whiteboard. If students can not use whiteboard because of the limitation of their height, please low down the whiteboard under the help of professional technician. 9.2 USB Cable Do not put the USB cables on the floor where it may stumble others. If you have to do so, straighten them and use insulated adhesive tape or cable with contrast color to tie them up.
