Installation guide
Observe the
following
warnings
when
using
this
unit.
OThe
driver
should
neither
watch
the
display
nor
operate the
system
while
driving.
Watching the display or operating the system will distract
the driver from driving safely and can cause
accidents. Always stop the vehicle
in
a safe location and use
the parking brake before watching the display or operating
the system.
OUse the
proper
power
supply.
This product
is
designed for operation with a negative
grounded
12
V
DC
battery system. Never operate this product
with other battery systems, especially a
24
V
DC
battery
system.
OKeep batteries and insulation film out of reach of
infants.
Batteries and insulation film can
be
ingested,
so
keep them
out
of
the reach
of
infants. If
an
infant ingests a battery or
insulation film, please seek immediate medical.
OProtect
the
radio.
Do
not insert any foreign objects into the slot of this unit.
000
not
disassemble
or
modify
the unit.
Do
not disassemble, modify the unit or attempt
to
repair the
product yourself. If the product needs
to
be
repaired, consult
your dealer or Retro Manufacturing directly.
000
not
use
the
unit
when
it
is
out
of
order.
If the unit
is
out of order (no power, no sound) or in
an
abnormal state (has foreign objects
in
it,
is
exposed
to
water,
is
smoking, or smells), turn it off immediately and
consult your dealer.
OThe remote
control
unit
should
be loose in the
car,
If the remote control unit is loose
in
the
car,
it could fall
on
the
floor while driving, get wedged under the brake pedal, and lead to
a traffic accident.
ORefer
fuse
replacement
to
qualified
service personnel.
When the fuse blows out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service technician. Incorrect replacement of the fuse may lead
to
smoke, fire, and damage to the product.
Observe the
following
cautions
when
using
this
unit.
OKeep the
sound
volume
at
an appropriate level.
Keep the volume level low enough
to
be
aware of road and
traffic conditions while driving.
000
not
insert
or
allow
your
hand
or
fingers
to
be
caught
in the
unit.
To
prevent injury, do not get your hand or fingers caught
in
moving parts or
in
the disc slot. Especialiy keep infants from
doing
so.
Observe the
following
cautions
when installing.
Refer
wiring
and
installation
to
qualified
service
personnel.
Installation
of
this unit requires special skills
and
experience.
For maximum safety, have
it
installed by your dealer.
Retro Manufacturing
is
not liable for any problems resulting from
your own installation of the unit. Please
be
sure to follow our
instructions carefully before attempting installation
Follow
the
instructions
to
install
and wire the product.
Not following the instructions
to
properly install and wire the
product could cause
an
accident or fire.
Take care
not
to
damage
the
leads.
When wiring take care not to damage the leads. Prevent
them from getting caught
in
the vehicle chassis, screws, and
moving parts such
as
seat rails. Do not scratch, pull, bend or
twist the leads. Do not run them near heat sources or place
heavy objects
on
them. If leads must
be
routed around sharp
metal edges, protect the leads by winding them with vinyl
tape or similar protection.
Use
the
designated
parts
and
tools
for
installation.
Use
the supplied or designated parts and appropriate tools
to
install the product. The use of parts other than those supplied
or designated may result
in
internal damage
to
the unit.
Faulty installation may lead to
an
accident, a malfunction or
fire.
ODisconnect
the lead
from
the negative H battery
terminal
before
installation.
Wiring and installation with the negative
(-)
battery terminal
connected may cause electrical shock and injUry due
to
a
short circuit.
Some cars equipped with the electrical safety system have
specific procedures for battery terminal disconnection.
FAILURE TO FOLLOW THIS PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION
OF
THE ELECTRICAL SAFETY
SYSTEM RESULTING
IN
DAMAGE
TO
THE VEHICLE AND
PERSONAL INJURY OR DEATH.
ONever use safety-related
components
for
installation,
grounding,
and
other
such
functions.
Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.
Olnstalling
the
product
on
the
air bag
cover
or
in a
location
where it
interferes
with
airbag
operation
is
prohibited.
Oln
the
case
of
installation
to
an
airbag-equipped car,
confirm
warnings
and
cautions
of
the
vehicle
manufacturer
before
installation.
OCheck
for
piping,
gasoline
tank, electric
wiring,
and
other
items
before
installing
the
product.
If you need to open a hole
in
the vehicle chassis
to
attach or
wire the product, first check where the wire harness, gasoline
tank, and electric wiring are located. Then open the hole
from outside if possible.
QNever install the
product
in a location where
it
interferes
with
your
field
of
vision.
ONever
have
the
power
cord
branched
to
supply
other
eqUipment
with
power.
OAfter
installation
and
wiring,
you
should
check
the
normal
operation
of
other
electrical
equipment.
The continuation
of
their use
in
abnormal conditions may
cause fire, electrical shock or a traffic accident.
OMake
sure
the
leads
do
not
interfere
with
driving
or
getting
in and
out
of
the vehicle.
Olnsulate
all
exposed
wires
to
prevent
short
circuiting.
OThis
unit
is
designed
for
use
exclusively
in automobiles.
000
not
operate the
unit
for
a
prolonged
period
with
the
engine
turned
off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
000
not
expose the
unit
to
direct
sunlight
or
excessive
heat.
OtherNise these
wi!!
raise the interior temperature of the
unit, and it may lead to smoke, fire, or other damage
to
the
unit.
000
not
use the
product
where
it
is
exposed
to
water,
moisture,
or
dust.
Exposure of the unit to water, moisture, or dust may lead
to
smoke, fire, or other damage
to
the unit. Make especially
sure that the unit does not get wet
in
car washes or on rainy
days.