Owners manual

ManualsBrandsRetrax ManualsAutomotive40722 RetraxPRO Retractable Tonneau Cover Fits 05-19 Frontier

Scan here to view a brief video

on how to install a

RETRAX cover.

Make sure that you have a

QR Code reader application

installed on your smartphone.

Manufactured in the USA by

APPLIED PRODUCTS, INC.

An Employee Owned Company

917 South 46th Street

Grand Forks, ND 58201

(701) 746-5596 (Fax) 746-5598

www.retrax.com

retrax@retrax.com

800-206-4070

Assembled View

Front Cover

Please Save Instructions:

Important Warranty and Maintenance

information enclosed

(2) 10-24 Black flathead Allen Screws

Passenger Side Rail

(has “inspected by” sticker under rail)

(4) 10-32 Screws

(stainless)

Spiral Canister

Tailgate End

Cab End

Exploded View

Front Cover

#4072 Nissan Frontier

Installation Instructions (with or without UtiliTrack Option)

Owner’s Manual

Summary of content (12 pages)

PAGE 1
#4072 Nissan Frontier Installation Instructions (with or without UtiliTrack Option) Owner’s Manual Please Save Instructions: Important Warranty and Maintenance information enclosed (2) 10-24 Black flathead Allen Screws Front Cover Tailgate End Passenger Side Rail (has “inspected by” sticker under rail) (4) 10-32 Screws (stainless) Front Cover Exploded View Cab End Spiral Canister Assembled View Manufactured in the USA by APPLIED PRODUCTS, INC.
PAGE 2
ASSEMBLY AND INSTALLATION INSTRUCTIONS Thank you for your purchase of the RETRAX™ bed cover system. Please read and follow instructions Before un-boxing and assembling the bed cover check for shipping damage. Keep boxes and packing until installation is complete. Unpack carefully to prevent scratching. Remove protective films from cover and canister after installation is complete. REMOVE the protective plastic films before exposing to direct sunlight.
PAGE 3
ASSEMBLY AND INSTALLATION INSTRUCTIONS Shipping tube STEP 1 Remove the shipping bracket and yellow wire. Completely remove white shipping tubes. Shipping bracket Remove these items only! The shipping brackets can be disassembled simply by removal of the 10-32 screws fastened to each side of the canister (Remove these items only). The tailgate can then be lifted away from the canister allowing for the removal of the shipping bracket by sliding the T-channel out from the wire ties.
PAGE 4
ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 2 continued. Slide the rail over the cover until the two threaded holes in the rail are lined up behind the two holes in the spiral. Attach using two of the 10/32 by 7/16" screws. Tighten using a manual #2 Phillips screwdriver. DO NOT USE LOCTITE! USE OF LOCTITE VOIDS WARRANTY STEP 3 Install the drivers rail. Pull the cover out of the canister 6”-8” (See PowertraxPRO Installation Supplement on how to mover electric cover).
PAGE 5
ASSEMBLY AND INSTALLATION INSTRUCTIONS 2005-up NISSAN FRONTIER with UTILITRAC OPTION If your truck does not have the Nissan Utilitrack rail option disregard this page and go to Step 5 on next page. If your truck does have the Utilitrack rail option, follow instructions through STEP 4. Then remove all 8 white nylon rail adjustment spacers from the rails and proceed with instructions below. You will not be using the 4 C-clamps. TOOLS NEEDED: T40 Torx wrench and 7/16” wrench. The hardware used is shown below.
PAGE 6
ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 5 Lift the assembled cover into the bed. Roll the cover into the canister and push down firmly on the rounded end of the lock until it latches. Close the tailgate on the pickup. Using two people, lift the bed cover by the front of the rail and two feet to the back. Set the assembly in place at the very front of the bed. NOTE: The rubber weather-strip on the front cover should lie on top of the pickup’s front rail - pointed towards the cab.
PAGE 7
ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 9 Measure the distance between the rails. The rails must be the same distance apart from each other (parallel) from the front to the rear. The following steps show how to measure and adjust the rails. Measurements are taken at 3 places starting at the front. The photo to the right shows measurement being taken with a tape measure. Measurements are taken here at the top of the rails (right above the weather-stripping) Drivers rail rear view STEP 9 a.
PAGE 8
ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 11 Check for proper fit between the front cover and the rolling cover. Using the lock handle, pull the cover closed over the tailgate and latch. The amount of weatherstrip showing at the front of the rolling cover should be close to equal on both the passenger and drivers sides. (Photo shows unpainted parts for clarity) If there is less weather-strip exposed on one side, adjust that rail by removing the clamps and moving that rail towards the cab.
PAGE 9
RetraxPRO MAINTENANCE AND USE INSTRUCTIONS USE The Retrax cover has superior quality, rail weather-strip seals. These seals help minimize water intrusion into the pickup bed. The initial break-in period for the rail weather-strip is about 48 hours in the fully closed position. Your cover may be slightly harder to open and close during the break-in period.
PAGE 10
Warranty Statement Applied Products, Inc. (referred to as manufacturer) warrants each new RetraxPRO retractable pickup bed cover to the original owner as follows: The RetraxPRO has a limited life me warranty for the failure of materials and workmanship. Warranty replacement costs will be prorated a er three (3) years.
PAGE 11
‐ The manufacturer does not undertake responsibility to any purchaser for warranty express or implied by any of its dealers, distributors or agents beyond which is contained herein.
PAGE 12
Made in the USA by An Employee Owned Company