Owners manual

ManualsBrandsRetrax ManualsAutomotive10841 RetraxONE Retractable Tonneau Cover Fits 07-19 Tundra

Manufactured in the USA by

APPLIED PRODUCTS, INC.

An Employee Owned Company

917 South 46th Street

Grand Forks, ND 58201

(701) 746-5596 (Fax) 746-5598

www.retrax.com

retrax@retrax.com

TOLL FREE 1-800-206-4070

Assembled View

Front Cover

Driver Side Rail

(has white lock stop)

(2) 10-24 Screws

Passenger Side Rail

(has “inspected by” sticker under rail)

(4) 10-32 Screws

(stainless)

Spiral Canister

Tailgate End

Cab End

Exploded View

Please save Instructions:

Important Warranty and Maintenance

information enclosed

#1084 Toyota Tundra 07-up

Installation Instructions (with or without Deck Rail Option)

Front Cover

Scan here to view a brief video

on how to install a

RETRAX cover.

Make sure that you have a

QR Code reader application

installed on your smartphone.

Owner’s Manual

Summary of content (12 pages)

PAGE 1
#1084 Toyota Tundra 07-up Installation Instructions (with or without Deck Rail Option) Owner’s Manual Please save Instructions: Important Warranty and Maintenance information enclosed Driver Side Rail (has white lock stop) (2) 10-24 Screws Front Cover Tailgate End Front Cover Passenger Side Rail (has “inspected by” sticker under rail) (4) 10-32 Screws (stainless) Cab End Exploded View Spiral Canister Assembled View Manufactured in the USA by APPLIED PRODUCTS, INC.
PAGE 2
ASSEMBLY AND INSTALLATION INSTRUCTIONS Thank you for your purchase of the RETRAX™ bed cover system. Please read and follow instructions before un-boxing and assembling the bed cover. Check for shipping damage. Keep boxes and packing until installation is complete. Unpack carefully to prevent scratching. Remove protective films from cover and canister after installation is complete. Remove the protective plastic films before exposing to direct sunlight.
PAGE 3
ASSEMBLY AND INSTALLATION INSTRUCTIONS Pre-assembly guidelines Two people are recommended for installation and you should allow 1 to 1 ½ hours to complete. Floor space about the size of pickup box is needed for assembly of the bed cover and rails. Clear out the pickup box and clean the front and side bed rails. Plastic bed liners may have to be cut or notched at the front of the bed if they touch the rolling cover or interfere with proper canister location.
PAGE 4
ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 2 Install the passenger rail to the spiral. Passenger rail has “inspected by” sticker under the front of the rail. Bearings enter channel of rail here. Front attachment hole Rear attachment hole Start sliding the cover and bearings into the channel of the rail. View from driver side Slide the rail over the cover until the two threaded holes in the rail are lined up behind the two holes in the spiral. Attach using two of the 10/32 by 7/16" screws.
PAGE 5
ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 3 Install the driver rail. Lift up the lock cover and open lock by pressing release button. Pull the cover out of the canister 6”-8” (See PowertraxONE Installation Supplement on how to move electric cover). Caution: DO NOT allow cover to roll back into canister until rail is installed. Repeat Step #2 to install the driver's rail. Be sure all rail mounting screws are tight. SIDE VIEW OF FRONT COVER This end towards tailgate STEP 4 Install the front cover.
PAGE 6
ASSEMBLY AND INSTALLATION INSTRUCTIONS Step 5-Ra and STEP 5Rb is for Toyota Tundra with the Deck Rail System STEP 5-Ra For Deck Rail systems refer to the information below before lifting cover onto truck Remove and save the black plastic cap at the rear of the Deck Rail track system on both sides of the truck (Figure 1). Loosen and slide out the movable truck tie downs on each side of the bed. Insert (1) mounting cleat into the track system on each side, position it about 15” from the front of the bed.
PAGE 7
ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 7 Install the front set of clamps. Start with the two clamps closest to the canister. If your model has two sizes of clamps, the clamps for the front are marked CAB. Proper clamp location is between the two adjustment screws. The adjustment screws are set at different depths depending on your model. These screws may be adjusted later. DO NOT ADJUST NOW! The clamps should be installed as high up as possible to engage more teeth on the rail.
PAGE 8
ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 9 Measure the distance between the rails. The rails must be the same distance apart from each other (parallel) from the front to the rear. The following steps show how to measure and adjust the rails. Measurements are taken at 3 places starting at the front. The photo to the right shows measurement being taken with a tape measure. Measurements are taken here at the top of the rails (right above the weather-stripping) Drivers rail rear view STEP 9 a.
PAGE 9
ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 11 Check for proper fit between the front cover and the rolling cover. Using the lock handle, pull the cover closed over the tailgate and latch. The amount of weatherstrip showing at the front of the rolling cover should be close to equal on both the passenger and drivers sides. (Photo shows unpainted parts for clarity) If there is less weather-strip exposed on one side, adjust that rail by removing the clamps and moving that rail towards the cab.
PAGE 10
Maintenance and Use Instructions USE The Retrax cover has superior quality, rail weather-strip seals. These seals help minimize water intrusion into the pickup bed. The initial break-in period for the rail weather-strip is about 48 hours in the fully closed position. Your cover may be slightly harder to open and close during the break-in period.
PAGE 11
Applied Products, Inc. th 917 S. 46 Street Grand Forks, ND 58201 www.retrax.com ▪ retrax@retrax.com ▪ 1-800-206-4070    RetraxONE ™ Warranty Information Never allow any person or animal to be transported in the pickup bed. Under no circumstances should anyone stand, sit or lay on the cover. The RetraxONE ™ bed cover is not waterproof. Applied Products, Inc. will not be held liable for damage sustained to any cargo being transported in a pickup bed equipped with a RetraxONE ™ bed cover.
PAGE 12
Made in the USA by An Employee Owned Company