Installation Manual

Pg. 16
Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  



5.5’ - 6.5’ bed WITH Utili-track:
t has the Utili-track uses the
4 clamps below.
5.5’ - 6.5’ bed WITHOUT Utili-track:
8’ bed WITH Utili-track:









UT Utili-track:









The Titan with no Utili-track uses the 4 clamps
above.
Pg. 16
Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED 



Pg. 16
Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  



Pg. 16
Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  



Pg. 16
Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  



Pg. 16
Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
t , (pg. 2) then refer
o this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  



Pg. 16
Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  



Pg. 16
Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  



STEP 1: Remove plastic caps STEP 2: Insert mounting cleats
Pg. 16
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  



Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Continue with the standard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  





NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:

Option 2:
(disregard further reference to tie downs.)
Option 3: 

STEP 3: Re-insert tie downs and 2nd cleat





Pg. 16
Nissan Titan 2004-up
STEP 2: Insert mounting cleats


 


 
Conti dard
instructions at step 4 (pg. 2)
NOTE: The factory tie-downs may cause
interference with the lock when rolling.
Option 1:  
 
Option 2: 
(disregard further reference to tie downs.)
Option 3: 

 
 .
 

 
  closest to the front of the
bedImportant: Hole should be toward bottom of
channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

 important  

Rear View Passenger Rail
Mounting
Cleat
C-Channel
RETRAX Rail
Adjustment
screw
Bolt
Check the parts shown here, this model has different requirements than the standard parts.
WITHOUT Utili-track:
The Titan with no Utili-track uses the
clamps above. Continue with the
standard instructions on Page 1.
WITH Utili-track:
Follow standard instructions
through step 3, (pg. 2) then refer
back to this guide on
how to install mounting hardware.
The Titan that has the Utili-track uses the clamps below.
STEP 3: Re-insert tie downs and 2nd cleat
STEP 1: Remove plastic caps
FOR TITAN 5.5’ BED  






closest to the front of the bed.
Important: Hole should be toward bottom of channel.
FOR STEP 5 ON STANDARD INSTRUCTIONS:

important 

FOR TITAN 5.5’ BED:
󳭩󴰡󴵪󵕢󵌡󵩱󴡤󴱳󰝥󴱱󵭩



Continue with the standard instructions on
Page 2.
Follow standard instructions through step 3,
(pg. 2) then refer back to this guide on
how to install mounting hardware.
Continue with the standard
instructions at step 4 (pg. 3)
9
Nissan Titan2004-up Installation