Instructions / Assembly

11
2.2.2. Unroll the enclosed paper Measuring Tape (K) and place its 67 inch
mark at the top extremity of the Lateral Insect Screen Track (J) WITH the
black brushweatherstrip. (See Figure 2.2.2A, and right side of Figure
2.2.2B)
Fold the remaining 1/4 inch of tape so it falls down the top extremity side of
Lateral Insect Screen Track (J). See Figure 2.2.1B.
Unica A-7 Modification: USE this modification ONLY for Model Unica
A-7.
For model Unica A-7 which is only 52 inches long, unroll the enclosed
paper Measuring Tape (K) and place tape (K) with its 52 inch mark at
the top extremity of the Lateral Insect Screen Track (J) WITH the black
brushweatherstrip.
Fold the remaining 10 and 1/4 inch of tape (K) so it falls down the top
extremity side of Lateral Insect Screen Track (J) as shown in Figure 2.2.2B.
2.2.3. Retrieve the measurement you recorded in Box H in Step 2.1 above;
as Inside Side Jamb Height (window opening height) = H inches. MARK
the enclosed Measuring Tape (K) at “H inches” (the window opening
height measurement determined in Step 2.1. above.) At this point the
Measuring Tape (K) should be still unrolled atop Lateral Insect Screen
Tracks (J) so you can mark the cutting point on Measuring Tape K, and
then transcribe/mark the cutting point on the Lateral Insect Screen Tracks
(J) so you can cut at Mark “H” inches ON the Lateral Insect Screen Tracks
(J).
2.2.4. CUT both Lateral Insect Screen Tracks (J and J) at the same time,
at the “H inches” height you determined in Step 2.1. as the INSIDE SIDE
JAMB HEIGHT (window opening HEIGHT). (See Figure 2.2.4.)
I
M
P
O
R
T
A
N
T
I
M
P
O
R
T
A
N
T
!
Figure 2.2.2A Figure 2.2.2B
Figure 2.2.4
STEP 2.3. Drill Holes into Lateral Insect Screen Tracks for Attachment
to Window Side Walls.
2.3.1. Unroll your measuring tape on one of the Lateral Insect Screen Tracks
(J) and using the measuring tape as a guide, MARK the Side Insect Screen
Track (J) about 4 inches (10 cm) from the end. (See Figure 2.3.1.)
Repeat the steps in 2.3.1. for the second Lateral Insect Screen Track
(J)
2.3.2. Drill a hole with a 5/32 in.(3.97mm) drill bit where you marked. (See
Figure 2.3.2.)
Repeat the steps in 2.3.2. for the second Lateral Insect Screen Track (J)
If the height or installation conditions require it additional holes can be
drilled into the Side Insect Screen Tracks (J) by subdividing the distance
between the two previously drilled holes by half.
Figure 2.3.1
Figure 2.3.2
STEP 2.4. Prepare and Secure Black Brushweatherstrips.
2.4.1. As detailed in Section 2.2.1. above, please ensure that the
brushweatherstrips inside the Lateral Insect Screen Track (J) are STILL
all 4 aligned at one end, leaving the other end of the Lateral Insect Screen
Track without any brushweatherstrips for the last approximately 2 inches
(5 cm.) of the Lateral Insect Screen Track (J). (Those last 2 inches will
accomodate the Side Insect Screen Stoppers (L) inserted by you in Step
2.4.2. below). The side of the Lateral Insect Screen Tracks (J) that has
NO brushweatherstrip will become the bottom of retractable insect screen
frame structure resting on the window Sill.
MARK
CUT