Installation Guide

13
3.1.2. Install the Lateral Insect Screen Tracks (J)
Ensure that the Lateral Insect Screen Track (J) brushweatherstrip side is
facing the interior of the window opening. That is; facing the side screen
track on the opposite side of the window. (See Figure 3.1.2A)
Ensure that the Side Insect Screen Stopper (L) is in position. The Right
Lateral insect Screen Track should have the Stopper (L) in the Right
Channel. The Left Lateral Insect Screen Track should have the Stopper (L)
in the Left Channel
Figure 3.2B shows the Left Side Insect Screen Track with the Stopper (L)
in the left channel and the Lateral Insect Screen Track (J) Stopper (L) at
the bottom. The brushweatherstrip is above the Stopper (L) and facing the
Interior of the window opening. (See Figure 3.1.2B)
Start inserting the Lateral Insect Screen Track (J) into the Screen Cartridge
Header (A) by aligning the Left Lateral Insect Screen Track (J) with the
center of the leftmost side of the Screen Cartridge Header (See Figure
3.1.2C)
INSERT ONE Lateral Insect Screen Track (J) at a time into the sides of the
Screen Cartridge Header (A).
Insert the LEFT Lateral Insect Screen Track (J) into the protruding plastic
appendage on the Screen Cartridge Header (A). (See Figure 3.1.2C)
Be careful to center the Lateral Insect Screen Track (J) onto the appendage
from the Screen Cartridge Header (A) so as to be able to guide the Lateral
Insect Screen Track (J) to be pushed evenly into a parallell position to the
wall or window sides.
Move the Lateral Insect Screen Tracks (J) vertically so that they move INTO
the window jamb opening Make sure Lateral Insect Screen Tracks (J) insert
completely. (See Figure 3.1.2D)
REPEAT step 3.2.3. for the RIGHT Lateral Insect Screen Track (J)
Ensure that the Lateral Insect Screen Track (J) is aligned with the window
opening so that the distance from the corner of the wall is consistent and
so that the Lateral Insect Screen Track (J) on the left side of the window
is aligned with the Lateral Insect Screen Track (J) on the right side of the
window.
Using the included screws (M) affix the Lateral Insect Screen Tracks (J)
to the window's wall, by drilling screws (M) through the holes you drilled in
Step 2.3. (See Figure 3.1.2E)
Screw the included screws (M) into the Lateral Insect Screen Tracks (J)
AND into the window jamb walls.
CLOSING THE RETRACTABLE BUG SCREEN... using the pull cord (C)
pull down the Pull Bar, when Pull Bar is within your reach grab the Pull
Bar Handles (B) and continue lowering the mosquito screen until it reaches
the apposite latch position, where you will slightly push rotate the handles
slightly downward towards the window sill and towards outside in order to
securely close. (See Figure 3.3)
OPENING THE RETRACTABLE BUG SCREEN… put your fingertips IN
the handles (B) with your fingertips pointing down towards the window sill,
then apply slight forward/outward (toward outside) push pressure with the
front of your knuckles. (Rotating the handle downward toward the Sill and
then slight upward towards you)
Your knuckles should be pushing toward the outside or window and your
fingertips pointing toward the sill and then towards you as you execute the
rotation of the front of your knuckles outward.
Figure 3.1.2A
Figure 3.1.2B
Figure 3.1.2C
Figure 3.1.2D
Figure 3.1.2E
Figure 3.3
J
A
J
A
A
J
Lateral Screen
Track (J) facing
window interior.
Stopper (L)
in channel facing
window as
opposed to
channel facing
inside home.
L
insert (L) in
interior channel