Instruction Manual

32
■
Antenna Connection
Please connect an antenna before transmitting. Select the an-
tenna with the corresponding frequency and install on the ANT
antenna base. Use the antenna and coaxial feeder with the
VDPHQDWXUDOLPSHGDQFHȍ
NOTE: Do not transmit before connecting the antenna, it will
ruin the transceiver.
To the Antenna
Antenna Connector
Feeder Connector
■
Installation of Connecting Cables





When connecting the external speaker, GPS, DC power supply,
computer and navigation device by the rear panel cable end,
cover the connectors and cables with rubber vulcanzing tape as
below, to prevent water seeping into the transceiver.
Rubber Vulcanzing Tape
1. External Speaker and Programming Data Leads
y
Connect an external speaker to Blue and Black Lead.
%OXHĺ3RVLWLYH(OHFWURGH%ODFNĺ1HJDWLYH(OHFWURGH
(-).
y
Connect programming cable to Orange and Grey Lead.
2. NMEA In/Out Leads
Through the rear panel lead, this transceiver can connect
GPS input signals from GPS receivers, and can also output
GPS signals to other devices.
y
Input Connection:&RQQHFWWRWKH10($RXWSXWOLQHSRUW
of the GPS receiver for location data, connect as follows:
*UHHQĺ5HFHLYLQJ'DWD*36,QSXW<HOORZĺ5HFHLYLQJ
'DWD*36,QSXW
NOTE: GPS receiver is required to be compatible with
10($YHUVLRQRUDERYHVWDWHPHQWIRUPDW50&
GGA, GNS, GLL.
y
Output Connection: Connect the output to the navigation
GHYLFHLQSXWOLQHSRUWWKDWVXSSRUWV10($IRUUHFHLY-
ing location data from other ships, connect as follows:
%URZQĺ6HQGLQJ'DWD'DWD2XWSXW:KLWHĺ6HQGLQJ
'DWD'DWD2XWSXW
NOTE: The output signal of this transceiver complies with
10($YHUVLRQRUDERYHFRPSDWLEOHZLWK'6&'6(
navigation equipment, statement format RMC, GSA, GSV.
3. External GPS Antenna
Connect to an external GPS antenna. This interface is only
available on models with GPS, and is not available on mod-
els without GPS.
NOTE: Make sure that the GPS antenna is installed in an
open, unobstructed position so that the satellite signal can
be received well. When installing the GPS antenna, use the
VXSSOLHGGRXEOHVLGHGWDSHWR¿[LW
4. Ground Terminal
Connect this terminal to a vessel ground to prevent electrical
shocks and interference from other equipment occurring.
Use a PH M3×6 mm screw (not supplied).
5. DC Power Connector
5HG3RVLWLYH%ODFN1HJDWLYH7KHRXWSXWYROWDJHRI
the connected DC power supply must be 13.8V, do not con-
nect the transceiver to the 24V storage battery. If the current
supplied to the transceiver is insufficient, the display may
darken during transmission or the transmitting output power
PD\GURSVLJQL¿FDQWO\
NOTE: Connect the DC power cable to the 13.8V DC power
supply. Notice that the positive and negative polarity of the
terminal should be connected correctly.
D
Connected to the ship’s main power source
AC220V
If the ship’s main power supply AC220V/50Hz is to be used,
a separate DC stabilized voltage power supply device is re-
quired, with an output voltage of 13.8V and an output current
of 15A.
Fuse Box
Output:
DC13.8V / 15A
Red (+)
To AC Outlet
DC Stabilized Voltage
Power Supply Device
Black (í)