Night Stand Contains One (1) Night Stand and Hardware IMPORTANT NOTE: Carefully remove all the parts from the box, Arrange on a flat TOOLS REQUIRED: surface and verify you have all of the following parts and hardware -Phillips Screwdriver 1.Top Panel (1 PC) 2.Bottom Panel (1 PC) 3.Left Side Panel (1 PC) 4 Right Side Panel (1 PC) 5.Back Panel (1 PC) 6.Legs (4 PCS) 7.Drawer Front Panel (1 PC) 8.Drawer Bottom Panel (1 PC) ~~ 9.Drawer Left Side Panel A < 3 10.Drawer Right Side Panel 11.
HARDWARE LIST A.Allen Key (1 PC) B.Dowel (8 PCS) C.JCBC W 40mm (4 PCS) Se D. Minifix Bolt (4 PC) ~~ E. Minifix House (4 PCS) F. Minifix Cap (4 PCS) G.Screw 30mm (10 H.Screw 16mm I.Screw 50mm PCS) (12 PCS) (8 PCS) J. Handle Screw 35mm K.Nail (28 PCS) L.Handle (1 PC) (2 PCS) mommy O— & M.
ASSEMBLY INSTRUCTIONS STEP 1 Tap Dowels into the Left and Right Side Panels (Part 3) and (Part 4) in the larger holes provided. STEP 2 Using a Phillips Head Screwdriver, attach Mini fix Bolts (D) to the Top Panel (Part 1).
ASSEMBLY INSTRUCTIONS Insert Mini fix House (Part E) into the Left and Right Side Panels (Part 4 and 3) as shown.Ensure the open side of the Mini fix House is facing the opening on the left and right side Attach the Drawer Slider (Part M) to the Left Side Panel (Part 3) using Screw 16mm (Part the Pilot Hole as marked.
ASSEMBLY INSTRUCTIONS Attach the Drawer Slider (Part M) to the Right STEP 5 § Side Panel (Part 4) using Screw 16mm (Part the Pilot Hole as marked. . .o Attach the Top Panel (Part 1) to the Right Side STEP 6 This is how a mini fix works... Panel (Part 4) as shown. Turn the Mini fix House The head of the mini fix : : or housing goes into the open {Part E) to tighten using the Allen Key or mouth of the mini fix bolt. screwdriver.
ASSEMBLY INSTRUCTIONS Attach the Top Panel (Part 1) to the Left Side Panel (Part 3) as shown. Turn the Mini fix House (Part E) to tighten using the Allen Key or screwdriver. Cover the Mini fix House using the Mini fix Cap (Part F) by pressing it into the Mini fix House. ‘This is how a mini fix works... The head of the mini fix 297% housing goes into the open ‘mouth of the mini ix bolt. You then turn the mini fix Yh: housing spit tightens = over the mini fix bolt. a 7% *Attach Mini fix Cap as shown.
ASSEMBLY INSTRUCTIONS STEP 9 “Without edging/veneer facing downward Attach the Legs (Part 6) to the Bottom Panel (Part 2) in the holes provided using 8 30mm Screws (Part G) and a Phillips Head Screwdriver. x8 ® TS STEP 10 Attach the Back Panel (Part 5) by using the Nail (Part K) as shown.Be sure to attach nails on all 4 sides of the back panel to secure properly.
ASSEMBLY INSTRUCTIONS STEP 11 Attach the Left and Right Drawer side panels (Parts 9 and 10) to the Drawer Front Panel (Part 7) using Screw 50mm (Part I) as shown. Insert the Drawer Bottom Panel (Part 8) as shown. Attach the Drawer Back Panel (Part 11) to the Left and Right Drawer Side Panels using Screw 50mm (Part Step 11.2 Back View Attach the Drawer Bottom Bar (Part 12) using the Screw 30mm (Part G) and Nail (Part K) as shown.Attach Screw 16mm (Part H) to slider (Part M) as shown.
ASSEMBLY INSTRUCTIONS STEP 13 Attach Handle Screw (Part J) to the Handle (Part L) through Drawer Front Panel (Part 7) using a fillips head screwdriver.
