Service manual

ENGLISH
E-7
E-18
FEATURES AND SPECIFICATIONSOPERATION
Remote Control Operation
Operation available with
the Remote Control:
.Fan Speed
.Operation time Setting
.Auto
.UV Lamp On/Off
.Negative Ion On/Off
.RESET1
.RESET2
Multi-Stage Filters
The unit utilizes a two stage electrostatic precipitator combined with a Microbiologic Pre-filter (for large
particles), an Activated Carbon Filter (for odors and gases), UV germicidal light (killing airborne pathogen),
a Photo catalytic filter (removes VOC's) and a Negative ion generator.
Automatic Function
The gas sensor(odor sensor) can let the unit automatically select the appropriate fan speed depending on
the air quality detected.
Filter and UV Lamp Replacement Indicator
The "FILTER" and "UV LAMP" replacement indicators tell you when to replace the Activated Carbon Filter
and the UV lamp.
Safety Micro-Switch (Interlock Switch)
This air purifier is equipped with a safety interlock switch (Micro-safety switch) that will turn the unit off if
the front panel is removed while the unit is running.
Easy Maintenance and Low Cost
When the electrostatic precipitator(Electronic cell) needs to be washed or the filters need to be replaced,
simply open the front panel and lift out the electronic cell or old filters and drop the new or clean one in.
No screws, hooks or tools are required. The electronic cell captures small particles on aluminum plates
that are simply rinsed off in the sink. There are no expensive filters to replace.
Standby Power
In order to operate the electrical circuits while the power plug is inserted in the wall outlet, this product
consumes about 2W of standby power. For energy conservation, unplug the power cord when the unit
is not in use.
Model No.
Power Requirement
Rated Power
Fan Motor
Fan Speed CFM
Applicable Floor Surface
(Ceiling height 8')
Noise Level
Negative Ion
UV Lamp
Cord Length
Dimensions
Weight
RespirAide 301F
120V,60Hz,1.1A
130W
120V,60Hz,0.8A
H-300,M-135,L-88
1 air exchange per hour: 2257 sq.ft.
2 air exchanges per hour: 1129 sq.ft.
5 air exchanges per hour: 451 sq.ft.
19 air exchanges per hour: 10 x 12 sq.ft.
<55dB
>1.2x10
6
pcs/cc
6Wx2
2.5m (8.3 ft)
153cm(H)x45cm(W)x28cm(D)
38kg
FEATURES
SPECIFICATIONS
Remote Control Use
1.Operate with the remote control facing the main unit receiver.
2.The signal range is about 19 feet (6 m).
3.Make sure there are no objects blocking the path of the signal.
4.Avoid dropping or damaging the remote control.
5.Do not use it in high humidity conditions or in direct sunlight or near a heat source.
The unit will start operating when
the POWER Button is pressed.
Pressing the button again will stop
operation.
Auto Button
At AUTO mode, the fan
speed is automatically
switched (H, M, L)
depending on the
amount of pollution in
the air.
Transmitter
RESET2 Button(UV Lamp Reset Button)
After UV lamp replacement, ensure to
press the button 12 times for initialization.
Before pressing the Filter Reset Button, be
sure that the unit is plugged in.
RESET1 Button(Filter Reset Button)
After replacement of Activated Carbon Filter,
make sure to press the button 12 times for
initialization.
Before pressing the Filter Reset Button, be
sure that the unit is plugged in.
Neg.Ion Button
When pressed, the
generation of ions will
cease and the Negative
ion generator light on
the control panel will go
out.
Swing Button
When pressed,the louver
will swing horizontally.
UV Lamp Button
When pressed,UV lamp
will go out.
Speed Button
The fan speed can be
switched among Low,
Medium and High settings.
Night Button
When pressed,all the indicator
lights on the display panel will
go out.
Timer Button
The set time switches every
time the button is pressed as
shown below.
*The applicable floor surface area is appropriate for operating the unit at maximum fan speed.
Power Night
Speed
Swing Auto
UV Lamp Neg.Ion
RESET1 RESET2
Timer
Power (ON/OFF) Button
1hr-2hr-3h......10hr-11hr-12hr
Cancel
**The indicator light shows
the set time.