User guide

Revision 1.0 Page 10 of 29
Warning
Please Note
The specifications of the product detailed on this
Set-Up Guide may change without notice. RDM
Ltd. shall not be liable for errors or for incidental
or consequential damages, directly and indirectly,
in connection with the furnishing, performance or
misuse of this product or document.
Ensure that all power is
switched off before
installing or maintaining
this product
Mercury 3 M & E Installation Guide
www.resourcedm.com
Parameter Tables
Not all parameters apply to all controller types. For example P-08 is the Superheat reference which only applies to the EEV variant of
controllers (available types on the E are 3, 4, 5 & 6). This parameter will not appear if the controller is a Mechanical variant. In the
following table, the type columns on the right hand side will be greyed out if that parameter does not apply to that controller type.
Number
Parameter
Range
o
C (
o
F )
Step
Units
Default LT
o
C (
o
F )
Default HT
o
C (
o
F )
M
Type
1&2
M
Type
3&4
M
Type
5&6
E
Type
3&4
E
Type
5&6
P-01
Cut-in Temp.
-42 to 30 (-43.6 to 86)
0.1
Deg
-20 (-4)
0.0 (32)




Cut-in Temp.
(Integral)
-42 to 30 (-43.6 to 86)
0.1
Deg
-20 (-4)
3.5 (38.3)

P-02
Diff.
0 to 10 (0 to 18)
0.1
Deg
2 (3.6)
1.5 (2.7)




Diff. (Integral)
0 to 10 (0 to 18)
0.1
Deg
2.5 (4.5)
2.5 (4.5)

P-03
Control Weight
0 to 100
1
%
50
50




Control Weight
(Integral)
0 to 100
1
%
40
30

P-04
Display Weight
0 to 100
1
%
50
50




Display Weight
(Integral)
0 to 100
1
%
40
30

P-05
Lag Comp Delay
00:00 to 15:00
00:05
mm:ss
00:40
00:10

P-06
Anti SC Time
00:00 to 15:00
00:05
mm:ss
03:00
03:00

P-07
Lag Cut Out Diff
0 to 10 (0 to 18)
0.1
Deg
2.5 (4.5)
2.5 (4.5)

P-08
Superheat Ref
0 to12 (7.2 to 21.6)
0.1
Deg
6 (10.8)
6 (10.8)


P-09
Response On
1 to 30
1
10
10


P-10
Response Off
1 to 30
1
10
10


P-11
Control Type
0 = EEV 1 = EET
2 = EEV/T
1
0
0


P-51
EEV Minimum
Opening
0 - 100%
1
%
10
10


P-52
Superheat Problem
0 – 12
o
C (0 – 21.6
o
F)
0.1
Deg
0
0


P-53
Superheat EEV
Problem Opening
0 - 100%
1
%
10
10


P-54
Superheat EEV
Problem Time
00:00 to 99:00
01:00
mm:ss
03:00
03:00


P-56
EEV Start Opening
0 - 100%
1
%
10
10


P-55
Average Valve
Opening
0 - 100%
1
%
100
100


P-57
EEV Divide Value
0 - 100%
1
%
50
50


P-12
Relay 4 Mode
0 = Suction Line
1 = Trim Heater
2 = Alarm
3 = Remote
4 = Trim Hub
1
0
0


Relay 4 Mode
(Coldroom)
0 = Suction Line
1 = Alarm
2 = Remote
1
0
0


P-13
Trim in Defrost
0 (Off), 1(On)
0
0


P-14
Trim Level
0 to 100
1
%
100
100


P-85
Key-switch Mode
0 = Case Off
1 = Fans only
2 = toggle
3 = Off
1
0
0





P-87
Control Probe type
0 = Use Air on Probe
1 = Use Log Probe
1
0
0





P-90
Resistor Case Off
0 (Disabled),1(Enabled)
0
0





P-92
Fans temperature
mode
0 = Off
1 = Temperature
2 = Over-temperature
3 = Temp/OT
1
0
0





P-93
Fans Off
Temperature
-42 to 30 (-43.6 to 86)
0.1
Deg
-10 (14)
8 (46.4)





P-83
Fan Control
0 = Off
1 = Run
2 = Pulse
1
1
1


P-78
Fan Pulse On
00:00 to 99:00
01:00
mm:ss
05:00
05:00


P-79
Fan Pulse Off
00:00 to 99:00
01:00
mm:ss
30:00
30:00

