Power Station II BATTERY PACK User Guide English Respiratory Care Solutions
Power Station II BATTERY PACK / AKKUPACK / BATTERIE / ALIMENTATORE A BATTERIA / BATERÍA / BATERIA / ACCU / BATTERIPACK / BATTERIPAKKE / BATTERIPAKKE / AKKU / ΜΠΑΤΑΡΙΑ / 电池包 / 電池包 2 A 2 1 3 a b B 1 5 2 3 7 6 7 6 5 4 9 4 8 C 2 3 1 a DC plug / Gleichstromstecker / Fiche CC / Spinotto DC / Enchufe de CC / Ficha CC / DC-stekker / DC-kontakt / Jævnstrømsstik / Likestrømsstøpsel / Tasavirtaliitin / Βύσμα DC / 直流电电源插头 / 直流電電源插頭 b Example cable illustration only / Abbildung eines Beispielkab
D 1 * 2 3 4 E 1 2 3 4 * 5 6 Excluding Elisée / Ausschließlich Elisée / Hors Elisée / Escluso l’Elisée / Excepto Elisée / Excluindo o Elisée / Exclusief Elisée / Exklusive Elisée / Undtagen Elisée / Unntatt Elisée / Ei Elisée / Δεν περιλαμβάνεται το Elisée / 不包括Elisée呼吸机 / 不包括Elisée呼吸機 F 1 2 3a * 3b *Example device illustration only / Abbildung eines Beispielgerätes / Exemple d’appareil / Illustrazione dell’apparecchio a solo titolo di esempio / Ilustración del dispositivo proporcionada a mod
Power Station II DC output voltage & DC cables 24V VPAP™ III ST-A S9™ Series Stellar™ VPAP III ST-A with QuickNav ™ VPAP™ Auto 25 VPAP™ S, VPAP™ ST VPAP™ IV, VPAP™ IV ST S8™ Auto 25 VS III™ Elisée™ 150 26V DC Cable Part Number 24959 24959 24960 24960 24960 24960 24961 24959 (24981 for Stellar™ Mobility bag) 24963 24962 English Notes: •• Not all devices are available in all regions. •• For information on battery run times refer to the Battery/Compatibility List on www.resmed.
Svenska Obs! •• Vissa utrustningar finns inte i alla delar av världen. •• För information om batteriernas körtider hänvisas till Produktkompatibilitetslista för batterier/ utrustningar på www.resmed.com. Dansk Bemærkninger: •• Det er ikke alle apparater, der kan fås i alle lande. •• Der er oplysninger om batteriers driftstid under Liste over kompatible batterier og apparater på webstedet www.resmed.com. Norsk Merknader: •• Noen apparater er ikke tilgjengelig i alle land.
English Intended use The ResMed Power Station II (RPS II) is an external lithium-ion battery that provides power when mains power is unavailable. Please read the entire guide before using the RPS II. Refer to the device user guides for intended patients, uses and contraindications associated with CPAP, bilevel and ventilation therapy. RPS II at a glance Refer to illustration A. The RPS II system comprises the following components: 1. Battery 2. Power supply unit adapter 3.
Setting up CAUTION •• Ensure the RPS II and the device are turned off before setting up. •• When the RPS II is plugged to the mains power supply, ensure all cables are properly connected. Charging the battery Refer to illustration C. 1. Attach the power supply unit adapter to the DC plug and connect into the battery DC input/output port. 2. Connect the AC power cord to the power supply unit. 3. Plug the other end of the AC power cord into the mains power outlet.
2. Plug the battery coupler cables into each of the battery DC input/output ports. The battery coupler cables are marked with ‘1’ (primary) and ‘2’ (reserve) labels. 3. a. When charging two batteries, attach the power supply unit adapter to the DC plug and connect the adapter to the the battery coupler. b. When powering a device, connect the DC output cable of the device to the end of the battery coupler.
Using humidifiers When a device integrated with the HumidAire 2i™ or H4i™ humidifier is not connected to the mains power supply, the humidifier will only operate in passive unheated mode despite the warm-up message appearing on the device. When the device is connected to the mains power supply, it will return to active heated mode. S9™ and H5i™ devices operate normally in active heated mode when connected to the battery or to the mains power supply.
Troubleshooting If there is a problem, try the following suggestions. If the problem cannot be solved, contact your equipment supplier or ResMed. Do not attempt to open the battery. Problem/Possible cause Solution Device is not running Power connections are disrupted. Check all cables and connect them as described in Setting up. RPS II is discharged. Connect the device to the mains power supply and recharge the RPS II. RPS II is off. Set the DC on/off switch to on. Incorrect output voltage selected.
Technical specifications Battery technology Capacity UN classification Power supply Battery output voltage Power supply unit output current (rated) Battery output current (rated) Standby current Protection Dimensions (L x W x H) Battery weight System weight Minimum life cycle Operating conditions Charging Discharging Transport/storage conditions Operating/storage air pressure Recharge time Electromagnetic compatibility IEC 60601-1 classification Battery run time 1 Lithium ion < 100 Wh (97 Wh) UN3481 (lit
Symbols The following symbols may appear on the device or packaging: Attention, consult accompanying documents; Drip proof; No protection; Read instructions before use; Class II equipment; European RoHS; 8 Batch Code; Serial number; Catalogue number; Temperature limitation (storage and transport); level; Audible alert mute; package is damaged; DC input/output; Manufacturer; Charging; O I DC on/off; Maximum humidity; Battery charge Do not use if European Authorised Representative; Environme
•• Make sure to periodically recharge the battery due to effects of selfdischarging. •• As the battery ages, the available capacity decreases. When the remaining battery capacity is getting low, do not rely on the RPS II as the primary supply. •• Ensure the internal battery of any connected device is kept charged up to provide backup power in the event of loss of power from RPS II. •• Only use a supplied ResMed 90W AC power supply unit for charging the RPS II.
Limited warranty ResMed Ltd (hereafter ’ResMed’) warrants that your ResMed product shall be free from defects in material and workmanship from the date of purchase for the period specified below.
This warranty gives you specific legal rights, and you may also have other rights which vary from region to region. For further information on your warranty rights, contact your local ResMed dealer or ResMed office.
248527/2 2012-07 Power Station II USER ROW MULTI Respiratory Care Solutions Manufacturer: ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia. Distributed by: ResMed Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA. ResMed (UK) Ltd 96 Milton Park Abingdon Oxfordshire OX14 4RY UK. See www.resmed.com for other ResMed locations worldwide. For patent information, see www.resmed.com/ip. Designs pending. HumidAire, H4i, H5i, Stellar, VPAP and S9 are trademarks of ResMed Ltd.
