User Guide

ManualsBrandsResideo Braukmann ManualsHeating Supplies1" Union Sweat Mixing Valve, 70-180 F (Heating Only)

Table Of Contents

62-3106—01

PRODUCT DATA

AM-1 SERIES “R Model” - Heating Only

PROPORTIONAL THERMOSTATIC MIXING AND DIVERTING VALVE PATENTED

SPECIFICATIONS

Temperature Range: 70° - 180° F (21° - 82° C).

Maximum Hot Water Inlet Temperature: 212° F (100° C).

NOTE: Consult PEX tubing manufacturer for maximum

allowable temperature ratings.

Maximum Pressure Rating: 150 psi (1034 kPa).

Minimum Required Temperature Difference between hot

and mix 3° F (-16° C).

Minimum Flow: 0.5 Gpm (1.9 Lpm).

Body Material: Nickel plated Brass/Bronze construction,

Teflon coated valve body wear surface, Teflon coated brass

shuttle, EPDM O-rings, proportional design (simultaneous

control of hot and cold ports), with either sweat union, NPT

(female) union or union PEX connections.

Valve Body: Refer to Fig. 7.

Connections: Union Sweat, Union NPT (female) and Union

PEX.

Dimensions: Refer to Fig. 1.

Contents

Specifications ................................................................... 1

Product Information .......................................................... 1

Valve Adjustment ............................................................. 2

Application ........................................................................ 2

Installation ........................................................................ 2

Ordering Information ........................................................ 2

Operation ......................................................................... 3

Valve Maintenance ........................................................... 3

Typical Specification ......................................................... 4

PRODUCT INFORMATION

• HEATING ONLY (Not intended for potable water usage).

•Teflon

coated spool and body to prevent mineral

buildup and extended valve life.

• Lockable Handwheel.

• Nickel plated brass/bronze construction, EPDM

O-rings.

• Constant water temperature under different operating

conditions.

• Proportional valve (simultaneous control of hot and

cold water).

• Straight thru design (hot and cold at same level).

• Designed for easy maintenance and element

replacement (Refer to page 4).

• Union Sweat, Union Threaded, and Union PEX

connections available (Refer to Table 1).

• Patent No. 6,079,625.

Summary of content (4 pages)

PAGE 1
AM-1 SERIES “R Model” - Heating Only PROPORTIONAL THERMOSTATIC MIXING AND DIVERTING VALVE PATENTED PRODUCT DATA PRODUCT INFORMATION • HEATING ONLY (Not intended for potable water usage). • Teflon® coated spool and body to prevent mineral buildup and extended valve life. • Lockable Handwheel. • Nickel plated brass/bronze construction, EPDM O-rings. • Constant water temperature under different operating conditions. • Proportional valve (simultaneous control of hot and cold water).
PAGE 2
AM-1 SERIES “R MODEL” - HEATING ONLY Table 1. AM-1 Union Connections. Size Max Flow in. Connection Type GPM Product Number AM100R-US-1 1/2 AM101R-US-1 3/4 AM102R-US-1 Cv in. A in. (mm) B in. (mm) C in. (mm) 8 2.7 (69) 4.4 (112) 12 2.9 (73) 4.9 (124) 1 16 3.5 (89) 6.1 (155) AM100R-UT-1 1/2 8 2.9 (73) 4.8 (122) AM101R-UT-1 3/4 AM102R-UT-1 1 AM100R-UPEX-1 1/2 AM101R-UPEX-1 3/4 Union Sweat Union Threaded 12 Union PEX 3.15 (80) 3.8 (97) 6.5 (165) 16 3.9 (99) 7.
PAGE 3
AM-1 SERIES “R MODEL” - HEATING ONLY Mixing Applications (Constant Supply Temperature) CAUTION Do Not Install Pump Between Connection “A” and Heat Source. The installation of the pump at this point would result in NO FLOW through the radiation loop(s). SuperVent H HEAT SOURCE M (2) EXPANSION C TANK (BOILER, WATER HEATER, etc.) PUMP Z AM SERIES Z Z ZONE VALVES RADIANT FLOOR LOOP A PUMP M25429 Fig. 2. Single Loop.
PAGE 4
AM-1 SERIES “R MODEL” - HEATING ONLY HANDWHEEL RETAINING RING UPPER NUT LOWER NUT To Clean and/or Replace the Lower Assembly Shut Off Water and: 1. 2. 3. TOP ASSEMBLY O RING LOWER ASSEMBLY WARNING 4. 5. DIFFUSER SPRING H H MIX With a screwdriver remove screw and hand wheel. Unscrew lower nut (counterclockwise). This removes top assembly. Brass top assembly will pop up. Remove lower assembly, diffuser and spring. C VALVE BODY Do not use solvents or scratch metallic / Teflon coated surfaces.