User Manual Foot and Calf Massager Model: R-D001RS
Introduction Thank you for choosing the RENPHO Foot and Calf Massager. Please use this product with the utmost care and safety in mind. To ensure safety and avoid any accidental damage or injury, please read this manual carefully and use the product only as indicated. Non-compliance may cause serious injuries, death and/or severe property damage.
not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair. 6) Do not carry this appliance by supply cord or use cord as a handle. 7) Keep the cord away from heated surfaces. 8) Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like. 9) Never drop or insert any object into any opening. 10) Do not use outdoors.
DANGER: Keep Dry – Do not operate in a wet or moist condition. For household use only. Do not immerse in water. SAVETHESEINSTRUCTIONS About the RENPHO Foot and Calf Massager 1.Specification Model: R-D001RS Input: AC 100-240V 50/60Hz Rated Power: 60W Auto-off Timer: 15min/20min/30min Product Size: L584*W395*H246mm Product Weight:8.2kg 2.
3.Overview Suitable for calf circumference within 19.7 inches Heat 15 20 30 Time L M Control Panel H Knead Intensity 1 2 3 4 Air Intensity Air Mode Detachable foot cover with zipper Magnetic area designed to place the remote control Remote Control Power 4.
Using the Renpho Foot and Calf Massager When massaging calves, it is recommended to turn on only the Air pressure or Kneading function, and start from the lowest intensity. Massage Postures Massage Feet Massage Calves Massage Arms We recommend you limit massaging to 15-30 minutes. Longer massage time may cause mild pain. Operation 1. Connect the plug to the power source. The Power indicator flashes White accompanied by a beep sound and the massager enters standby mode. 2.
5. Press among 1/2/3/4. 6.Press the L/M/H/OFF. Button to adjust the Air Intensity Button to adjust the Knead Intensity among 7. Press the Button to turn ON/OFF the heating function or select Full (Bottom+Instep), Instep or Bottom, heating area. Note: A: Heating, Kneading and Air pressure function can work independently. B: Each press is accompanied by a beep sound and corresponding indicator light (When off, the LED goes out).
Product Care and Maintenance 1. The use of non-rated voltage is prohibited. 2. It is prohibited for non-professional personnel to repair the massager or replace parts. 3. Do not use or store the appliance in wet environments or high temperatures. 4. Unplug the power cord from the outlet after using. 5. Ensure that the operation of this product does not exceed more than 30 minutes at any given time. 6. If you feel unwell or in any unusual discomfort, please stop using the product immediately. 7.
11. The product is a temperature-protection device; it will automatically shut-off when the temperature exceeds the safe limit. Troubleshooting Guide Common problems Possible Cause The product does not work 1.Disconnected power or loose plug causing poor contact. 2.The power switch is off or time is up. 3.The motor auto shuts-off due to the device being on too long activating overheating protection. The massage intensity Is too high or too low 1.Your feet is positioned at the wrong angle.
No heating or insufficient heating 1. The heating function isn’ t turned on. 2. The working heat area might be bottom, not full/Instep. 3. The product structure and working principle limits how fast the bottom can heat up. Therefore, the heating-up may seem a bit slow, wait a few minutes longer. 4. The ambient temperature or the internal temperature of the product is too high, the heating function will be turned off because of the over-heated protection. 1. Press the ” Heat” button.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
