User manual
Operating instructions
LED sensor light, 4 x 0.2 W
Item no. 1005229
Intended use
The product is intended for use as an indoor light source. The product activates
automatically via the built-in motion detector (PIR sensor) or manually. The double-
sided adhesive pads on the back of the product allow you to mount it to a suitable
surface. Power supply is via three AAA batteries (not included).
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this
product. Using the product other than for its intended purpose as described above
can damage the product or pose a risk of injury. Read the instructions carefully and
keep them. Make this product available to third parties only together with its operating
instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• LED sensor light with 2 adhesive stripes
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
• Correct polarity must be observed while inserting the (rechargeable)
batteries.
• (Rechargeable) batteries should be removed from the device if it is not
used for a long period of time to avoid damage through leaking. Leaking
or damaged (rechargeable) batteries might cause acid burns when in
contact with skin, therefore use suitable protective gloves to handle
corrupted (rechargeable) batteries.
• (Rechargeable) batteries must be kept out of reach of children. Do not
leave (rechargeable) batteries lying around, as there is risk, that children
or pets swallow them.
• All (rechargeable) batteries should be replaced at the same time.
Mixing old and new (rechargeable) batteries in the device can lead to
(rechargeable) battery leakage and device damage.
• (Rechargeable) batteries must not be dismantled, short-circuited or
thrown into re. Never recharge non-rechargeable batteries. There is a
risk of explosion!
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modications and repairs are to be performed exclusively
by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Function of the motion detector
• The PIR sensor integrated in the product responds to temperature changes within
the detection range. Such is the case when humans or animals, whose temperatures
dier from the ambient temperature, enter the detection range.
• In order to allow for maximum detection, the product should be positioned in such
a way that the object to be detected does not walk towards the motion detector but
crosses the detection range from left to right or vice versa. Keep that in mind when
installing the product.
• The range of detecting temperature changes depends on a variety of factors:
- Installation height
- Ambient temperature
- Temperature dierence between the moving object and the environment
- Size of the object
- Distance between object and product
- Direction and speed of motion
Detecting temperature changes through glass is basically not possible. Do
not install the product behind a pane of glass.
Inserting / replacing batteries
• Push the lid on the back in the direction of the arrow to remove it.
• Correctly insert three AAA batteries, heeding the polarity markings inside the
battery compartment.
• Replace the lid. Align the ve pins on the underside of the lid to the corresponding
openings on the product. Push the lid in the opposite direction of the arrow until it
clicks into place.
Only one orientation is possible. Proceed carefully and do not use any force
to prevent breaking o the pins.
Change the batteries as soon as the light visibly dims or the product no
longer turns on.
Operation
• Push the lid on the back in the direction of the arrow to remove it.
• Use the switch next to the battery compartment to select the operating mode:
- ON: on permanently
- OFF: o permanently
- AUTO: automatic operation, motion detector activates light.
The motion detector is located at the middle on the front of the product.
• Replace the lid. Align the ve pins on the underside of the lid to the corresponding
openings on the product. Push the lid in the opposite direction of the arrow.
Only one orientation is possible. Proceed carefully and do not use any force
to prevent breaking o the pins.
• Turn o the product and remove the batteries for extended periods of disuse (see
previous chapter).