User manual

ManualsBrandsRENKFORCE ManualsCar Mobile Phone AccessoriesKFZ-SN1M Suction cup Car mobile phone holder Magnetic fastener

Operation

The metal plates may get magnetized to some extent during use.Users that carry a

pacemaker are strongly requested to discuss the use of the product with their doctor

rst. The metal plates may especially pause a risk when carrying the phone in the

pocket of a shirt or jacket.

a) Outer Metal Plate

If you are not using a case, attach it directly to your smartphone. Attach it to the

outside of your case if you are using one.

To protect your smartphone from getting scratched, please use the protective lm. It

will not leave any residue when removed.

• Clean surface, removing all lint, dust and dirt.

• Unpeel the protective lm cover, place on desired surface

(recommended).

• Unpeel the outer metal plate cover, attach the plate to the

outside of your device or case.

b) Inner Metal Plate

If you are using a thick case, use the outer metal plate and connect it to the outside

of the case.

• Clean surface, removing all lint, dust and debris.

• Unpeel protective lm cover, place on desired surface (optional).

• Unpeel the inner plate cover then attach the plate to the inside

surface of your phone case.

c) Suction Cup

The gel suction cup (5) can leave marks on or damage sensitive surfaces.

The gel suction cup (5) allows you to create a seal over textured or smooth surfaces.

First make sure the surface it is clean and free from lint, dust and debris.

• Raise the locking lever (2) to the up position.

• Press the gel suction cup (5) atly against a surface, then press the suction lever (2) down

to lock it in place.

Check that the mount is secure before attaching your smartphone to it. If the gel

suction cup (5) does not create a good seal it may need to be cleaned. See section

“Care and Cleaning” for more information.

To remove the mount, rst lift the locking lever then pull the tab located on the gel

suction cup (5) and peel away from surface.

d) Attaching Phone

• Place your phone onto the holder, making contact between the rubberized magnetic head (2)

and the metal plate. Max. phone weight, see technical data.

Make sure your phone is held rmly in place before letting go.

Care and Cleaning

• Over time the gel suction cup (5) may get covered in dust and debris. Rinse with warm water

and let air dry.

• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as

they can cause damage to the housing and malfunctioning.

• Clean the product with a dry, bre-free cloth.

Disposal

At the end of its service life, dispose of the product in accordance with applicable

regulatory guidelines.

You thus fulll your statutory obligations and contribute to the protection of the

environment.

Technical Data

Phone weight ................................ max. 300 g

Dimensions (W x H x D) ............... 69 x 88 x 95 mm

Weight .......................................... 77 g

Operating Instructions

Magnetic Smartphone Suction Cup Mount

Item No. 1647031

Intended Use

Use this device to magnetically attach your smartphone to different surfaces using a suction

cup mount. The rotating ball joint can be adjusted 360° and the hinge tilted to optimize viewing

angles. A sticky gel padded suction cup creates a better seal over textured surfaces and the

included metal plates allow you to mount with or without a smartphone case.

For safety and approval purposes, you must not rebuild and/or modify this product. If you use

the product for purposes other than those described above, the product may be damaged. In

addition, improper use can result in short circuits, res, or other hazards. Read the instructions

carefully and store them in a safe place. Make this product available to third parties only

together with its operating instructions.

This product complies with the statutory national and European requirements. All company

Delivery Content

• Device

• 2 x metal plates (inner and outer)

• Protective lm

• Operating instructions

Up-to-date Operating Instructions

Download the latest operating instructions at www.conrad.com/downloads or

scan the QR code shown. Follow the instructions on the website.

Explanation of Symbols

The symbol with the exclamation mark in the triangle is used to indicate important

information in these operating instructions. Always read this information carefully.

The arrow symbol indicates special information and advice on operation.

Safety Instructions

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information on

proper handling in this manual, we assume no liability for any resulting

personal injury or damage to property. Such cases will invalidate the warranty/

guarantee.

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become

dangerous playing material for children.

• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, steam and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height

can damage the product.

• Consult an expert when in doubt about the operation, safety or connection of the

appliance.

• Maintenance, modications and repairs must only be completed by a technician

or an authorised repair centre.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

Operating Elements

1 Rubberized magnetic head

2 Locking lever

3 Rotating ball joint (360°)

4 Hinge

5 Gel suction cup

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights

including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication

represents the technical status at the time of printing.