U-Reach Mini Duplicator PRO250 High Speed Portable HDD Duplicator User Guide V2.5 EN The Data Equipment Expert www.ureach-inc.
Content Index Disclaimer of Warranties Disclaimer of Warranties 5.1.7 Off-Line Scan Uncorrectable Sector Count 15 5.1.8 Seek Error Rate 16 5.1.9 Temperature 16 3 Before You Start Important Notice 4 Safety Precautions 5 Content Index 5.2 Update System 17 5.3 System Info. 17 5.4 Set Target HDD Content Index 4 Chapter ① - Product Introduction Capacity 17 5.5 Read Speed 18 18 1 Features 6 5.6 Write Speed 2 Product Overview 7 6 Setup 18 2.
Disclaimer of Warranties All HDD duplicators are made specifically for data backup with legal authorities from copyright owners. Any unauthorized action of copyright is strictly prohibited, and the original manufacturer disclaims all warranties or representations of illegal actions by users. The manufacturer also disclaims any liability for any of losses or damages due to not be able to perform its undertakings or provide any of the services attributable to any events or circumstances beyond our control.
Before you start Important Notice • Read the complete operation instruction carefully contributes to better operation. Make sure the source device is correct and workable. • • To guarantee data consistency, strongly suggest the capacity of source • and targets should be the same. It is strongly suggest to use “Copy+Compare” to achieve a perfect duplication. Safety Precautions • The warranty will expire if damage is incurred resulting from non• • • • • • compliance with theses operating instructions.
Chapter ➀ - Product Introduction 1 Features • • • • High copy speed supports for duplication and comparison. Support reading/writing speed measuring function. Show the detailed information of HDD and its quality. Auto power control system helps to protect the HDD from any damage during the insertion and removal from the duplicator. • Support compatibility of multiple interfaces via external adapters: • 2.5”/3.5” IDE HDD, mSATA SSD , eSATA , iVDR , microSATA, cFAST. Support HDD interfaces directly: 1.
Chapter ➀ - Product Introduction 2 Product Overview 2.1 System Overview Red : Fail Green : Pass Yellow : Powering Target port Source port Backward Forward / OK Cancel / Back 2.
Chapter ➀ - Product Introduction 3 Function Table Function Description 1. Copy To copy source HDD to multiple target HDDs. Refer to function [6.1 Copy Area] for 4 different copy modes selection. 2. Compare To compare data bit for bit between source and target HDDs. 3.Copy +Compare It makes copy first and then compare target HDD with source HDD to ensure data correctness. 4.1 Quick Erase To erase HDD’s index table only, it takes short time to execute this function. 4.
Chapter ➀ - Product Introduction 5.1.1 Model Number To show HDD's model number. 5.1.2 Version of Firmware To show HDD's firmware version. 5.1.3 Serial Number To show the serial number of HDD. 5.1.4 Device Power Cycle To show the count of HDD's turning on and off. 5.1 Show Disk Info. 5.1.5 Power-on Hours To show the total hours of HDD power-on. Select one port and enter 5.1.6 Reallocation Event Count the function. It represents the count of failing to save data. 5.1.
Chapter ➀ - Product Introduction 6.1.1 System and Files To copy source HDD's data area only. 6.1.2 ALL Partitions 6.1 Copy Area To copy source HDD's all partitions. 6.1.3 Whole HDD To copy the whole source HDD. 6.1.4 Percentage(%) To copy percentage range of source HDD. 6.2 Skip Error Set to ignore error of source HDD while copying. 6.3 Language English / Japanese 6.4.1 Unknown 6.4.1.1 Copy Unknown Format Set to Copy or Skip 6.4.1.2 Skip Unknown Unknown. 6.4.2 Erase Master 6.4.2.
Chapter ➁ -FunctionIntroduction 1 Copy It copies data from the source HDD to the target HDD. Please ensure you have selected the copy mode require before executing the copying process. Refer to function [6.1 Copy Area] for details. Copy Process Copie Time Copy 0:26 50% 2047M 1037M Total data capacity Copied data capacity Copy Process % Copy Result Pass 0:58 No Bad Sector! Note The default setting is the quick copy mode “System and Files”.
Chapter ➁ - Function Introduction 4 Erase There are Quick Erase, Full Erase, DoD Erase, DoD EraseComp , and Secure Erase, totally 5 kinds of erasing modes. Select the appropriate erase method when you would like to dispose or reuse the HDDs. Note •Users can go to Function [6.4.2 Erase Master] to select if erasing the source HDD. The default setting is “Disable” to erase the source HDD. •This function can be stopped while processing by pressing [ESC] for about 3~4 seconds. 4.
Chapter ➁ -FunctionIntroduction Erasing Erasing 1 HDD DoD Erase 2:05 [02] Erase[00] 465G 4818M The system will show the result after finishing DoD Erase Pass: 5 Fail: 0 4.4 DoD Erase Comp As well as DoD erase, this function will also execute compare function to make sure the random bit was correctly written.
Chapter ➁ - Function Introduction 4.5 Secure Erase The international authorized high standard Secure Erase function. It overwrites every single track on the hard drive with "00". Even PA/DCO or other data area which are not able to load, can be erased all together. Note •Please do not disrupt during Secure Erase, otherwise it would cause irretrievable error on HDD, which turns the HDD unusable. 5 Utility 5.1 Show Disc Info. The function will show basic information of both source and target HDDs. 5.1.
Chapter ➁ -FunctionIntroduction 5.1.4 Device Power Cycle This function is to show the count of HDD's turning on and off. [Disc Info.] 4.Device Power C [Device Power C] 99 5.1.5 Power-on Hours This function is to show the total hours of HDD powering-on. [Disc Info.] 5.Power-on Hours [Power-on Hours] 18 5.1.6 Reallocation Event Count This function is to show the count of reallocating event. When the HDD fails to save data, it will need to redefine the location to store data.
Chapter ➁ - Function Introduction 5.1.8 Seek Error Rate This function is to show the error rate of searching for data. It can represent the damage rate of data stored in the HDD. [Disc Info.] 8.Seek Error Rat [Seek Error Rat] 0 5.1.9 Temperature This function is to show the temperature of HDD. [Disc Info.] 9.Temperature [Temperature] 22 o C 5.2 Update System This function is to execute firmware updating of system. You can follow the following steps to update the system firmware. ⊳ Select Function [5.
Chapter ➁ -FunctionIntroduction ⊳ Download the BIOS from the PC to your HDD. HDD USB HDD Enclosure PC ⊳ Plug the HDD into Port 1of the duplicator, select Function 5.2.1 to update BIOS, and wait for about 1 minute to finish the update process. [Update System] 1.Update BIOS 5.3 System Info. This function shows the duplicator information such as model name and firmware version. HDD Dupe 1-1 Ver: 2.31.0 5.
Chapter ➁ - Function Introduction 5.5 Read Speed This function is to measure the reading speed of the HDD by reading the whole HDD. R 2:30 89.0M/S 465G 12.8G 5.6 Write Speed This function is to measure the writing speed of the HDD by writing the whole HDD. W 1:08 89.6M/S 465G 4423M Note •This function will delete the content in HDD, so please make sure you have backup data before executing this function. 6 Setup 6.1 Copy Area This setting is to select the copy mode you would like to use. 6.1.
Chapter ➁ -FunctionIntroduction Source HDD 320GB Data : 20GB Partition1 : 90GB Tatget HDD 320GB When choosing “System and Files Copy”, only 20G data will be copied, and it just takes 6.2% time compared to “Whole HDD Copy”. The target HDD will be exactly the same as source HDD after copy. Note •System and Files only supports FAT, NTFS, and LINUX (ext2/ ext3/ ext4). 6.1.2 All Partitions This mode will copy all of the partitions areas bit by bit including the free space.
Chapter ➁ - Function Introduction 6.1.3 Whole HDD This mode will copy the entire HDD, regardless of content, format, partition or free space. This mode will take much more time to duplicate the source HDD completely. [Copy Area] Whole HDD Source HDD 320GB Data : 20GB Partition1 : 90GB Tatget HDD 320GB When choosing “Whole HDD Copy”, completed 320GB HDD will be copied, and it takes the longest time. The target HDD will be exactly the same as the source HDD after copy.
Chapter ➁ -FunctionIntroduction Source HDD 500GB Data:250GB Partition:250GB Tatget HDD 500GB Only percentage range from25% to 32% will be copied. 25% 25% 32% 32% 500GB 6.2 Skip Error This function sets the volume of errors that is acceptable for you to skip during the copy process. [Skip Error] 0 Note • If it’s critical that there are no errors on the HDD, then the error counter should be set to 0. 6.3 Language Select preferred language. 6.4 Advanced Setup 6.4.
Chapter ➁ - Function Introduction [Unknown Format] Copy Unknown 6.4.1.2 Skip Unknown The setting skips the unknown format area during copy process. [Unknown Format] Skip Unknown 6.4.2 Erase Master This function is to set if erasing the source or not when executing erasing function. [Erase Master] Disable [Erase Master] Enable 6.4.3 Erase Pattern Select different erase method during the third time writing data for functions [4.3 DoD Erase] and [4.4 DoD EraseComp]. 6.4.3.
Chapter ➁ -FunctionIntroduction 6.4.3.2 Big Random Data A set of different random character to be written into a set of area. This erase pattern method is safer for preventing from data recovered. [Erase Pattern] Big Random Data 26A5C8781 BF51337E81 AA9641D3B 5CDA756B1 3BAFF21FF4 1FBAC4C99 7EDAF1237 7F51C59C3 6.4.4 Wait HDD Time You can select auto-start time after plugging in HDD, able to set the waiting time from 0 to 30 seconds. [Wait HDD Time] 15 seconds 6.4.
Chapter ➁ - Function Introduction ❶ Copy and Setting: Yes, copy. Copy data from source to target including HPA area of source. It will not only set the target HDD the same HPA setting as the source HDD, but also copy the data in the HPA area. ❷ No, Keep HPA: No, don't copy. Copy data from source to target and keep the target HPA setting during Copy. ❸ No, Clear HPA: No, don't copy. Copy data from source to target and remove the target HPA setting during Copy. ❹ No, Setting HPA: No, don't copy.
Chapter ➁ -FunctionIntroduction 6.4.7 Transfer Rate You can select the best transfer rate from UDMA 2 to UDMA7 for your HDD duplication process. If you are not confident on the HDD quality or you find a high failure rate on copy or compare. It is recommended to slow down the UDMA mode. [Transfer Rate] UDMA 5 6.4.8 Stop Motor Time When the system finishes executing functions, the motor won’t stop running immediately.
Chapter ➂ - Specification Product Name Carry Mini Super High Speed HDD Dupe Product Number PRO250 Targets 1:1 (2-port) Support HDD Interface Directly 1.8”/2.5”/3.5” SATA HDD and SSD Control Button 4 push buttons( ▲ , ▼ , OK, ESC ) Compatible HDD/SSD via Adapter All major brand of 2.5"/3.5" IDE HDD, mSATA SSD, eSATA, microSATA, iVDR, cFAST Duplication Mode 1.Quick Copy (System and Files only) 2.All Partitions Copy 3.Whole HDD Copy 4.
www.ureach-inc.
