7A Series Scanner User Guide
Table of Contents Chapter 1 Getting Started .............................................................................................................................................. 1 Introduction............................................................................................................................................................ 1 About This Guide........................................................................................................................................
Prefix Sequence ................................................................................................................................................. 29 Custom Prefix ..................................................................................................................................................... 30 Enable/Disable Custom Prefix .................................................................................................................. 30 Set Custom Prefix ...............
Add-On Code Required ............................................................................................................................. 50 ISSN ..................................................................................................................................................................... 51 Restore Factory Defaults ........................................................................................................................... 51 Enable/Disable ISSN.................
Restore Factory Defaults ........................................................................................................................... 71 Enable/Disable Code 39 ............................................................................................................................ 71 Check Digit Verification.............................................................................................................................. 72 Transmit Start/Stop Character .........................
Appendix .......................................................................................................................................................................... 91 Factory Defaults Table ...................................................................................................................................... 91 AIM ID Table .......................................................................................................................................................
** Enter Setup Chapter 1 Getting Started Introduction The 7A Series Scanner, armed with the patented computerized image recognition system, bring about a new era of 1D barcode scanning. The 7A Series Scanner’s 1D barcode decoder chip ingeniously blends technology and advanced chip design & manufacturing, which significantly simplifies application design and delivers superior performance and solid reliability with low power consumption.
** Enter Setup About This Guide This guide provides programming instructions for the 7A Series Scanner. Users can configure the scanner by scanning the programming barcodes included in this manual. The 7A Series Scanner has been properly configured for most applications and can be put into use without further configuration. Users may check the Factory Defaults Table in Appendix for reference. Throughout the manual, programming barcodes marked with asterisks (**) are factory default values.
** Enter Setup Configuring the Scanner Barcode Programming The 7A Series Scanner can be configured by scanning programming barcodes. All user programmable features/options are described along with their programming barcodes in the following sections.
** Enter Setup Factory Defaults Scanning the following barcode can restore the scanner to the factory defaults. User may need to reset scanner when: 1. Scanner is not properly configured so that it fails to decode barcodes; 2. User forget previous configuration and want to avoid its impact; 3. Functions that are rarely used have been enabled for the time being.
** Enter Setup Chapter 2 Scan Mode Manual Mode Manual Mode (default): A trigger pull activates a decode session. The decode session continues until the barcode is decoded or the trigger is released or the decode session timeout expires. ** Manual Mode Decode Session Timeout: This parameter sets the maximum time decode session continues during a scan attempt. It is programmable in 1s increments from 1s to 255s. The default timeout is 15s.
** Enter Setup Continuous Mode Continuous Mode: A trigger press activates the scanner to scan and decode at user-specified intervals, i.e. the timeout between decodes. Each decode session lasts until barcode is decoded or the decode session timeout expires. To suspend/resume the operation, simply press the trigger. Continuous Mode Decode Session Timeout: This parameter sets the maximum time decode session continues during a scan attempt. It is programmable in 1s increments from 1s to 255s.
** Enter Setup Timeout between Decodes:This parameter sets the timeout between decode sessions. When a decode session ends, next session will not happen until the timeout between decodes expires. It is programmable in 0.1s increments from 0.0s to 25.5s. The default timeout is 1.0s. Timeout between Decodes Example: Set the timeout between decodes to 5s 7 1. Scan the Enter Setup barcode. 2. Scan the Timeout between Decodes barcode. 3. Scan the numeric barcodes “5” and “0”.
** Enter Setup Timeout between Decodes (Same Barcode) can avoid undesired rereading of same barcode in a given period of time. This parameter sets the timeout between decodes for same barcode. It is programmable in 0.1s increments from 0.1s to 25.5s. The default timeout is 3.0s. If the parameter is set to 0, the timeout between decodes (same barcode) is infinite. Note: This parameter is only valid when the Disallow Rereading Same Barcode is enabled.
** Enter Setup Security Level 0-3 level. The higher the value, the lower the error rate and efficiency.
** Enter Setup Sense Mode Sense Mode: The scanner activates a decode session every time when it detects a change in ambient illumination and meets the requirement of the image stabilization timeout. Decode session continues until barcode is decoded or the decode session timeout expires. Sense Mode Decode Session Timeout: This parameter sets the maximum time decode session continues during a scan attempt. It is programmable in 1s increments from 1s to 255s. The default timeout is 15s.
** Enter Setup Image Stabilization Timeout: The scanner waits for the image stabilization timeout to expire before activating a decode session every time it detects a change in ambient illumination. This parameter is programmable in 0.1s increments from 0.0s to 25.5s. Image Stabilization Timeout Example: Set the Image Stabilization Timeout to 5s 11 1. Scan the Enter Setup barcode. 2. Scan the Image Stabilization Timeout barcode. 3. Scan the numeric barcodes “5” and “0”.
** Enter Setup Timeout between Decodes (Same Barcode) can avoid undesired rereading of same barcode in a given period of time. This parameter sets the timeout between decodes for same barcode. It is programmable in 0.1s increments from 0.1s to 25.5s. The default timeout is 3.0s. If the parameter is set to 0, the timeout between decodes (same barcode) is infinite. Note: This parameter is only valid when the Disallow Rereading Same Barcode is enabled.
** Enter Setup Sensitivity: This parameter specifies the degree of acuteness of the scanner’s response to changes in ambient illumination. The higher the sensitivity, the lower requirement in illumination change to trigger the scanner. You can select an appropriate degree of sensitivity that fits the ambient environment. High Sensitivity ** Medium Sensitivity ** Medium Sensitivity Custom Sensitivity Sensitivity levels range from 0 to 255. The smaller the number, the higher the sensitivity.
** Enter Setup Chapter 3 Notification Good Read Beep ** Good Read Beep On Good Read Beep Off Low Frequency ** Medium Frequency High Frequency Beep Duration: 40ms ** Beep Duration: 80ms Beep Duration: 120ms Exit Setup 14
** Enter Setup Decode Result Notification When enabled, if a barcode does not decode, “F” is transmitted; if a barcode is decoded, “S” is appended to the barcode data as the most left character.
** Enter Setup Other Settings You can change the following parameter settings temporarily and the changes will be lost when you power down or reboot the scanner. Silent Mode ** Silent Mode Off Silent Mode On Note: This feature is only applicable to decode beep and will be automatically disabled when the scanner is powered down or rebooted.
** Enter Setup Chapter 4 Communication Settings The scanner provides USB HID interface to communicate with the host device. The host device can receive scanned data.
** Enter Setup USB Interface USB HID-KBW When enabled, the scanner’s transmission is simulated as USB keyboard input. It works on a Plug and Play basis and no driver is required.
** Enter Setup Standard Keyboard ** Standard Keyboard Emulate ALT+Keypad When Emulate ALT+Keypad is enabled, any ASCII character (0x00 - 0xFF) is sent over the numeric keypad no matter which keyboard type is selected. Since sending a character involves multiple keystroke emulations, this method appears less efficient. 1. ALT Make 2. Enter the number corresponding to the ASCII character on the keypad. 3.
** Enter Setup Function Key Mapping When Function Key Mapping is enabled, function character (0x00 - 0x1F) are sent as ASCII sequences over the numeric keypad. 1. CTRL Make 2. Press function key (Refer to the ASCII Function Key Mapping Table on the following page) 3.
** Enter Setup ASCII Function Key Mapping Table ASCII Value ASCII Value Function Key （HEX） 21 Function Key （HEX） 00 2 10 P 01 A 11 Q 02 B 12 R 03 C 13 S 04 D 14 T 05 E 15 U 06 F 16 V 07 G 17 W 08 H 18 X 09 I 19 Y 0A J 1A Z 0B K 1B [ 0C L 1C \ 0D M 1D ] 0E N 1E 6 0F O 1F .
** Enter Setup USB Country Keyboard Types Keyboard layouts vary from country to country. All supported keyboard types are listed below. Exit Setup ** 1 - U.S.
** Enter Setup 23 9 – Germany (Austria) 10 - Greece 11 - Hungary 12 - Israel 13 - Italy 14 - Latin America 15 - Netherland 16 - Norway 17 - Poland 18 - Portugal Exit Setup
** Enter Setup Exit Setup 19 - Romania 20 - Russia 21 - Slovakia 22 - Spain 23 - Sweden 24 - Switzerland 25 - Turkey1 26 - Turkey 2 27 - UK 28 - Japan 24
** Enter Setup Inter-Keystroke Delay This parameter specifies the delay between emulated keystrokes.
** Enter Setup Convert Case This parameter is valid when the Standard Keyboard or Function Key Mapping is enabled. ** No Case Conversion Convert All to Upper Case Convert All to Lower Case Invert Upper and Lower Case Characters Example: When the Invert Upper and Lower Case Characters feature is enabled, barcode data “AbC” is transmitted as “aBc”.
** Enter Setup Emulate Numeric Keypad When this feature is disabled, sending barcode data is emulated as keystroke(s) on main keyboard. To enable this feature, scan the Emulate Numeric Keypad barcode. Sending a number (0-9) is emulated as keystroke on numeric keypad, whereas sending other character like “+”, “_”, “*” , “/” and “.” is still emulated as keystroke on main keyboard.
** Enter Setup Chapter 5 Data Formatting Introduction After a successful barcode read, a string containing numbers, letters or symbols will be returned. In real applications, barcode data may be found insufficient for your needs. You may wish to include additional information such as barcode type, data acquisition time or delimiter in data being scanned. Adding extra information to printed barcodes does not seem like a sensible solution since that will increase the barcode size and make them inflexible.
** Enter Setup Prefix Sequence ** Code ID+Custom+AIM ID 29 Custom+Code ID+ AIM ID Exit Setup
** Enter Setup Custom Prefix Enable/Disable Custom Prefix If custom prefix is enabled, you are allowed to append to the data a user-defined prefix that cannot exceed 5 characters. For example, if barcode data is “123” and custom prefix is “AB”, the host will receive “AB123”. Enable Custom Prefix ** Disable Custom Prefix Set Custom Prefix To set a custom prefix, scan the Set Custom Prefix barcode, the numeric barcodes corresponding to the hexadecimal value of a desired prefix and the Save barcode.
** Enter Setup AIM ID Prefix AIM (Automatic Identification Manufacturers) ID defines symbology identifier (For the details, see the AIM ID Table section in Appendix). If AIM ID prefix is enabled, the scanner will add the symbology identifier before the scanned data after decoding.
** Enter Setup CODE ID Prefix Code ID can also be used to identify barcode type. Unlike AIM ID, Code ID is user programmable. For the information of default Code ID, see the Code ID Table section in Appendix. Enable CODE ID Prefix ** Disable CODE ID Prefix Restore All Default Code IDs Restore All Default Code IDs Set Code ID Code ID can only consist of one or two English letters.
** Enter Setup Set Code ID Barcodes 33 Set Code 128 Code ID Set UCC/EAN-128 Code ID Set EAN-8 Code ID Set EAN-13 Code ID Set ISSN Code ID Set ISBN Code ID Set UPC-E Code ID Set UPC-A Code ID Exit Setup
** Enter Setup Set Code ID Barcodes (continued) Set Interleaved 2 of 5 Code ID Set Matrix 2 of 5 Code ID Set Industrial 25 Code ID Set Code 39 Code ID Set Codabar Code ID Set Code 93 Code ID Set Code 11 Code ID Set MSI Code ID Exit Setup 34
** Enter Setup Set Code ID Barcodes (continued) Set RSS-14, Code ID Set RSS-Limited Code ID (GS1 DataBar) (GS1 DataBar Limited) Set RSS-Expand Code ID (GS1 DataBar Expanded) 35 Exit Setup
** Enter Setup Custom Suffix Enable/Disable Custom Suffix If custom suffix is enabled, you are allowed to append to the data a user-defined suffix that cannot exceed 5 characters. For example, if barcode data is “123” and custom suffix is “AB”, the host will receive “123AB”.
** Enter Setup Set Custom Suffix To set a custom suffix, scan the Set Custom Suffix barcode, the numeric barcodes corresponding to the hexadecimal value of a desired suffix and the Save barcode. Note: A custom suffix cannot exceed 5 characters. Set Custom Suffix Example: Set the custom suffix to “CODE” (its hexadecimal value is 0x43/0x4F/0x44/0x45) 1. Scan the Enter Setup barcode. 2. Scan the Set Custom Suffix barcode. 3. Scan the numeric barcodes “4”,“3”,“4”,“F”,“4”,“4”,“4” and “5”.
** Enter Setup Terminating Character Suffix A terminating character, such as carriage return (CR) and line feed (LF), can be used to mark the end of data, which means nothing can be added after it. A terminating character suffix cannot exceeed 5 characters. Enable/Disable Terminating Character Suffix This parameter determines whether to append predefined terminating character suffix to the data.
** Enter Setup Set Terminating Character Suffix The scanner provides a shortcut for setting the terminating character suffix to 0x0D (CR) or 0x0D,0x0A (CRLF) or 0x09 (Horizontal Tab), and enabling it by scanning the appropriate barcode below.
** Enter Setup Chapter 6 Symbologies Introduction Every symbology (barcode type) has its own unique attributes. This chapter provides programming barcodes for configuring the scanner so that it can identify various barcode symbologies. It is recommended to disable those that are rarely used in order to increase the efficiency of the scanner. Global Settings Enable/Disable All Symbologies If all symbologies are disabled, the scanner can only identify programming barcodes.
** Enter Setup Code 128 Restore Factory Defaults Restore the Factory Defaults of Code 128 Enable/Disable Code 128 ** Enable Code 128 41 Disable Code 128 Exit Setup
** Enter Setup Set Length Range for Code 128 The scanner can be configured to only decode Code 128 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Code 128 barcodes with either the minimum or maximum length. If minimum length is same as maximum length, only Code 128 barcodes with that length are to be decoded.
** Enter Setup UCC/EAN-128 Restore Factory Defaults Restore the Factory Defaults of UCC/EAN-128 Enable/Disable UCC/EAN-128 ** Enable UCC/EAN-128 Disable UCC/EAN-128 Decode as Code 128 43 Exit Setup
** Enter Setup Set Length Range for UCC/EAN-128 The scanner can be configured to only decode UCC/EAN-128 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes UCC/EAN-128 barcodes with either the minimum or maximum length. If minimum length is same as maximum length, only UCC/EAN-128 barcodes with that length are to be decoded.
** Enter Setup EAN-8 Restore Factory Defaults Restore the Factory Defaults of EAN-8 Enable/Disable EAN-8 ** Enable EAN-8 Disable EAN-8 Transmit Check Digit EAN-8 is 8 digits in length with the last one as its check digit used to verify the integrity of the data.
** Enter Setup Add-On Code An EAN-8 barcode can be augmented with a two-digit or five-digit add-on code to form a new one. In the examples below, the part surrounded by blue dotted line is an EAN-8 barcode while the part circled by red dotted line is add-on code.
** Enter Setup Add-On Code Required This parameter is only valid when Enable 2-Digit Add-On Code and/or Enable 5-Digit Add-On Code is selected. EAN-8 Add-On Code Required ** EAN-8 Add-On Code Not Required EAN-8 Extension Disable EAN-8 Zero Extend: Transmit EAN-8 barcodes as is. Enable EAN-8 Zero Extend: Add five leading zeros to decoded EAN-8 barcodes to extend to13 digits. Convert EAN-8 to EAN-13: Add five leading zeros to decoded EAN-8 barcodes to make them compatible in format to EAN-13 barcodes.
** Enter Setup EAN-13 Restore Factory Defaults Restore the Factory Defaults of EAN-13 Enable/Disable EAN-13 ** Enable EAN-13 Disable EAN-13 Transmit Check Digit EAN-13 is 13 digits in length with the last one as its check digit used to verify the integrity of the data.
** Enter Setup Add-On Code An EAN-13 barcode can be augmented with a two-digit or five-digit add-on code to form a new one. In the examples below, the part surrounded by blue dotted line is an EAN-13 barcode while the part circled by red dotted line is add-on code.
** Enter Setup Add-On Code Required This parameter is only valid when Enable 2-Digit Add-On Code and/or Enable 5-Digit Add-On Code is selected.
** Enter Setup ISSN Restore Factory Defaults Restore the Factory Defaults of ISSN Enable/Disable ISSN Enable ISSN ** Disable ISSN Decode as EAN-13 51 Exit Setup
** Enter Setup ISBN Restore Factory Defaults Restore the Factory Defaults of ISBN Enable/Disable ISBN Enable ISBN ** Disable ISBN Decode as EAN-13 Exit Setup 52
** Enter Setup Set ISBN Format ** ISBN-13 53 ISBN-10 Exit Setup
** Enter Setup UPC-E Restore Factory Defaults Restore the Factory Defaults of UPC-E Enable/Disable UPC-E ** Enable UPC-E Disable UPC-E Transmit Check Digit UPC-E is 8 digits in length with the last one as its check digit used to verify the integrity of the data.
** Enter Setup Add-On Code A UPC-E barcode can be augmented with a two-digit or five-digit add-on code to form a new one. In the examples below, the part surrounded by blue dotted line is a UPC-E barcode while the part circled by red dotted line is add-on code.
** Enter Setup Add-On Code Required This parameter is only valid when Enable 2-Digit Add-On Code and/or Enable 5-Digit Add-On Code is selected. UPC-E Add-On Code Required ** UPC-E Add-On Code Not Required Transmit System Character The first character of UPC-E barcode is the system character.
** Enter Setup UPC-E Extension Disable UPC-E Extend: Transmit UPC-E barcodes as is. Enable UPC-E Extend: Extend UPC-E barcodes to make them compatible in length to UPC-A. Convert UPC-E to UPC-A: Extend UPC-E barcodes to make them compatible in format to UPC-A.
** Enter Setup UPC-A Restore Factory Defaults Restore the Factory Defaults of UPC-A Enable/Disable UPC-A ** Enable UPC-A Disable UPC-A Decode as EAN-13 Exit Setup 58
** Enter Setup Transmit Check Digit UPC-A is 13 digits in length with the last one as its check digit used to verify the integrity of the data. ** Transmit UPC-A Check Digit Do Not Transmit UPC-A Check Digit Transmit Preamble Character Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A barcode.
** Enter Setup Add-On Code A UPC-A barcode can be augmented with a two-digit or five-digit add-on code to form a new one. In the examples below, the part surrounded by blue dotted line is a UPC-A barcode while the part circled by red dotted line is add-on code.
** Enter Setup Add-On Code Required This parameter is only valid when Enable 2-Digit Add-On Code and/or Enable 5-Digit Add-On Code is selected.
** Enter Setup Interleaved 2 of 5 Restore Factory Defaults Restore the Factory Defaults of Interleaved 2 of 5 Enable/Disable Interleaved 2 of 5 ** Enable Interleaved 2 of 5 Exit Setup Disable Interleaved 2 of 5 62
** Enter Setup Check Digit Verification A check digit is optional for Interleaved 2 o 5 and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable: The scanner transmits Interleaved 2 of 5 barcodes as is. Do Not Transmit Check Digit After Verification: The scanner checks the integrity of all Interleaved 2 of 5 barcodes to verify that the data complies with the check digit algorithm.
** Enter Setup Set Length Range for Interleaved 2 of 5 The scanner can be configured to only decode Interleaved 2 of 5 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Interleaved 2 of 5 barcodes with either the minimum or maximum length.
** Enter Setup Matrix 2 of 5 (European Matrix 2 of 5) Restore Factory Defaults Restore the Factory Defaults of Matrix 2 of 5 Enable/Disable Matrix 2 of 5 ** Enable Matrix 2 of 5 65 Disable Matrix 2 of 5 Exit Setup
** Enter Setup Check Digit Verification A check digit is optional for Matrix 2 of 5 and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable: The scanner transmits Matrix 2 of 5 barcodes as is. Do Not Transmit Check Digit After Verification: The scanner checks the integrity of all Matrix 2 of 5 barcodes to verify that the data complies with the check digit algorithm.
** Enter Setup Set Length Range for Matrix 2 of 5 The scanner can be configured to only decode Matrix 2 of 5 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Matrix 2 of 5 barcodes with either the minimum or maximum length. If minimum length is same as maximum length, only Matrix 2 of 5 barcodes with that length are to be decoded.
** Enter Setup Industrial 25 Restore Factory Defaults Restore the Factory Defaults of Industrial 25 Enable/Disable Industrial 25 ** Enable Industrial 25 Exit Setup Disable Industrial 25 68
** Enter Setup Check Digit Verification A check digit is optional for Industrial 25 and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable: The scanner transmits Industrial 25 barcodes as is. Do Not Transmit Check Digit After Verification: The scanner checks the integrity of all Industrial 25 barcodes to verify that the data complies with the check digit algorithm.
** Enter Setup Set Length Range for Industrial 25 The scanner can be configured to only decode Industrial 25 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Industrial 25 barcodes with either the minimum or maximum length. If minimum length is same as maximum length, only Industrial 25 barcodes with that length are to be decoded.
** Enter Setup Code 39 Restore Factory Defaults Restore the Factory Defaults of Code 39 Enable/Disable Code 39 ** Enable Code 39 71 Disable Code 39 Exit Setup
** Enter Setup Check Digit Verification A check digit is optional for Code 39 and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable: The scanner transmits Code 39 barcodes as is. Do Not Transmit Check Digit After Verification: The scanner checks the integrity of all Code 39 barcodes to verify that the data complies with the check digit algorithm.
** Enter Setup Transmit Start/Stop Character Code 39 uses an asterisk (*) for both the start and the stop characters. You can choose whether or not to transmit the start/stop characters by scanning the appropriate barcode below. ** Transmit Start/Stop Character Do Not Transmit Start/Stop Character Enable/Disable Code 39 Full ASCII The scanner can be configured to identify all ASCII characters by scanning the appropriate barcode below.
** Enter Setup Set Length Range for Code 39 The scanner can be configured to only decode Code 39 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Code 39 barcodes with either the minimum or maximum length. If minimum length is same as maximum length, only Code 39 barcodes with that length are to be decoded.
** Enter Setup Codabar Restore Factory Defaults Restore the Factory Defaults of Codabar Enable/Disable Codabar ** Enable Codabar 75 Disable Codabar Exit Setup
** Enter Setup Check Digit Verification A check digit is optional for Codabar and can be added as the last digit. It is a calculated value used to verify the integrity of the data. Disable: The scanner transmits Codabar barcodes as is. Do Not Transmit Check Digit After Verification: The scanner checks the integrity of all Codabar barcodes to verify that the data complies with the check digit algorithm.
** Enter Setup Start/Stop Character 77 ** Transmit Start/Stop Character Do Not Transmit Start/Stop Character ** ABCD/ABCD as the Start/Stop Character ABCD/TN*E as the Start/Stop Character abcd/abcd as the Start/Stop Character abcd/tn*e as the Start/Stop Character Exit Setup
** Enter Setup Set Length Range for Codabar The scanner can be configured to only decode Codabar barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Codabar barcodes with either the minimum or maximum length. If minimum length is same as maximum length, only Codabar barcodes with that length are to be decoded.
** Enter Setup Code 93 Restore Factory Defaults Restore the Factory Defaults of Code 93 Enable/Disable Code 93 ** Enable Code 93 79 Disable Code 93 Exit Setup
** Enter Setup Check Digit Verification Check digits are optional for Code 93 and can be added as the last two digits, which are calculated values used to verify the integrity of the data. Disable: The scanner transmits Code 93 barcodes as is. Do Not Transmit Check Digit After Verification: The scanner checks the integrity of all Code 93 barcodes to verify that the data complies with the check digit algorithm.
** Enter Setup Set Length Range for Code 93 The scanner can be configured to only decode Code 93 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Code 93 barcodes with either the minimum or maximum length. If minimum length is same as maximum length, only Code 93 barcodes with that length are to be decoded.
** Enter Setup Code 11 Restore Factory Defaults Restore the Factory Defaults of Code 11 Enable/Disable Code 11 Enable Code 11 Exit Setup ** Disable Code 11 82
** Enter Setup Check Digit Verification Check digits are optional for Code 11 and can be added as the last one or two digits, which are calculated values used to verify the integrity of the data. If the Disable option is enabled, the scanner transmits Code 11 barcodes as is.
** Enter Setup Set Length Range for Code 11 The scanner can be configured to only decode Code 11 barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes Code 11 barcodes with either the minimum or maximum length. If minimum length is same as maximum length, only Code 11 barcodes with that length are to be decoded.
** Enter Setup MSI Restore Factory Defaults Restore the Factory Defaults of MSI Enable/Disable MSI Enable MSI 85 ** Disable MSI Exit Setup
** Enter Setup Check Digit Verification Check digits are optional for MSI and can be added as the last one or two digits, which are calculated values used to verify the integrity of the data. If the Disable option is enabled, the scanner transmits MSI barcodes as is.
** Enter Setup Set Length Range for MSI The scanner can be configured to only decode MSI barcodes with lengths that fall between (inclusive) the minimum and maximum lengths. The supported maximum length is 255 characters. If minimum length is set to be greater than maximum length, the scanner only decodes MSI barcodes with either the minimum or maximum length. If minimum length is same as maximum length, only MSI barcodes with that length are to be decoded.
** Enter Setup RSS-14 (GS1 DataBar) Restore Factory Defaults Restore the Factory Defaults of RSS-14 (GS1 DataBar) Enable/Disable RSS-14 (GS1 DataBar) ** Enable RSS-14 (GS1 DataBar) Disable RSS-14 (GS1 DataBar) Transmit Application Identifier “01” ** Transmit Application Identifier “01” Exit Setup Do Not Transmit Application Identifier “01” 88
** Enter Setup RSS-Limited (GS1 DataBar Limited) Restore Factory Defaults Restore the Factory Defaults of RSS-Limited (GS1 DataBar Limited) Enable/Disable RSS-Limited (GS1 DataBar Limited) ** Enable RSS-Limited (GS1 DataBar Limited) Disable RSS-Limited (GS1 DataBar Limited) Transmit Application Identifier “01” ** Transmit Application Identifier “01” 89 Do Not Transmit Application Identifier “01” Exit Setup
** Enter Setup RSS-Expand (GS1 DataBar Expanded) Restore Factory Defaults Restore the Factory Defaults of RSS-Expand (GS1 DataBar Expanded) Enable/Disable RSS-Expand ** Enable RSS-Expand (GS1 DataBar Expanded) Exit Setup Disable RSS-Expand (GS1 DataBar Expanded) 90
** Enter Setup Appendix Factory Defaults Table Parameter Factory Default Remark System Settings Barcode Programming Enabled Programming Barcode Data Do not send Scan Mode Manual Mode Manual Mode Decode Session Timeout 15s 1-255s; 0: infinite. Decode Session Timeout 15s 1-255s; 0: infinite. Timeout between Decodes 1.0s Continuous Mode Reread Same Barcode Timeout between Decodes Disallowed 3.0s 0.1-25.5s Decode Session Timeout 15s 1-255s; 0: infinite.
** Enter Setup Parameter Factory Default Communication Interfaces Input Mode Standard Keyboard USB Country Keyboard TypeU.S.
** Enter Setup Parameter Factory Default Remark Code 128 Code 128 Enabled Minimum Length 1 Maximum Length EAN-8 80 EAN-8 Enabled Check Digit Transmit 2-Digit Add-On Code Disabled 5-Digit Add-On Code Disabled Add-On Code Not required Extend to EAN-13 Disabled No less than 1 (including check digit) EAN-13 EAN-13 Enabled Check Digit Transmit 2-Digit Add-On Code Disabled 5-Digit Add-On Code Disabled Add-On Code ISSN Not required ISSN Disabled ISBN ISBN Disabled ISBN Format
** Enter Setup Parameter Factory Default Remark UPC-E UPC-E Enabled Check Digit Transmit 2-Digit Add-On Code Disabled 5-Digit Add-On Code Disabled Add-On Code Extend to UPC-A Not required System Character UPC-A Do not transmit UPC-A Enabled Check Digit Transmit 2-Digit Add-On Code Disabled 5-Digit Add-On Code Disabled Add-On Code Preamble Character Interleaved 2 of 5 Not required Interleaved 2 of 5 Enbled Check Digit Verification Enabled Check Digit Do not transmit Minimum Le
** Enter Setup Parameter Factory Default Remark Matrix 2 of 5 Matrix 2 of 5 Enabled Check Digit Verification Disabled Check Digit Do not transmit Minimum Length 6 Maximum Length 80 No less than 2 (including check digit) Industrial 25 Industrial 25 Enabled Check Digit Verification Disabled Check Digit Do not transmit Minimum Length 6 Maximum Length 80 No less than 2 (including check digit) Code 39 Code 39 Enabled Check Digit Verification Disabled Check Digit Do not transmit St
** Enter Setup Parameter Factory Default Remark Codabar Codabar Enabled Check Digit Verification Disabled Check Digit Do not transmit Start/Stop Character Transmit Start/Stop Character Format ABCD/ABCD Minimum Length 4 Maximum Length 60 No less than 1 (including check digit) Code 93 Code 93 Enabled Check Digit Verification Enabled Check Digit Do not transmit Minimum Length 2 Maximum Length 80 No less than 1 (including check digit) Code 11 Code 11 Disabled Check Digit Verifica
** Enter Setup Parameter Factory Default Remark MSI MSI Disabled Check Digit Verification One check digit, MOD10 Check Digit Do not transmit Minimum Length 4 Maximum Length 60 No less than 2 (including check digit) RSS-14 (GS1 DataBar) RSS-14 (GS1 DataBar) Enabled AI (Application Identifier) Transmit RSS-Limited (GS1 DataBar Limited) RSS-Limited (GS1 DataBar Limited) Enabled AI (Application Identifier) Transmit RSS-Expand (GS1 DataBar Expanded) RSS-Expand (GS1 DataBar Expanded) 97 E
** Enter Setup AIM ID Table Symbology AIM ID Code 128 ]C0 Standard Code 128 ]C1 FNC1 is the character right after the start character ]E4 Standard EAN-8 UCC/EAN 128 (GS1-128) EAN-8 EAN-13 ]E4….]E1… EAN-8 + 2-Digit Add-On Code ]E4….
** Enter Setup Symbology AIM ID Code 93 ]G0 Not specified ]H0 One check digit, MOD11; transmit check digit ]H1 Two check digits, MOD11/MOD11; transmit check digit ]H3 Do not transmit check digit after verification ]H8 Two check digits, MOD11/MOD9; transmit check digit ]H9 No check digit verification ]M0 One check digit, MOD10; transmit check digit ]M1 One check digit, MOD10; do not transmit check digit ]M7 Two check digits, MOD10 /MOD11; do not transmit check digit ]M8 Two check digit
** Enter Setup Code ID Table Symbology Code ID Code 128 j UCC/EAN-128 u EAN-8 g EAN-13 d ISSN n ISBN B UPC-E h UPC-A c Interleaved 2 of 5 e Matrix 2 of 5(European Matrix 2 of 5) v Industrial 25 i Code 39 b Codabar a Code 93 y Code 11 z MSI m RSS-14 (GS1 DataBar) D RSS-Limited (GS1 DataBar Limited) C RSS-Expand (GS1 DataBar Expanded) R
** Enter Setup ASCII Table 101 Hex Dec Char 00 0 NUL (Null char.
** Enter Setup 1d 29 GS (Group Separator)
** Enter Setup 103 Hex Dec Char 1e 30 RS (Request to Send) 1f 31 US (Unit Separator) 20 32 SP (Space) 21 33 ! (Exclamation Mark) 22 34 " (Double Quote) 23 35 # (Number Sign) 24 36 $ (Dollar Sign) 25 37 % (Percent) 26 38 & (Ampersand) 27 39 ` (Single Quote) 28 40 ( (Right / Closing Parenthesis) 29 41 ) (Right / Closing Parenthesis) 2a 42 * (Asterisk) 2b 43 + (Plus) 2c 44 , (Comma) 2d 45 - (Minus / Dash) 2e 46 .
** Enter Setup Hex Dec Char 3b 59 ; (Semi-colon) 3c 60 < (Less Than) 3d 61 = (Equal Sign) 3e 62 > (Greater Than) 3f 63 ? (Question Mark) 40 64 @ (AT Symbol) 41 65 A 42 66 B 43 67 C 44 68 D 45 69 E 46 70 F 47 71 G 48 72 H 49 73 I 4a 74 J 4b 75 K 4c 76 L 4d 77 M 4e 78 N 4f 79 O 50 80 P 51 81 Q 52 82 R 53 83 S 54 84 T 55 85 U 56 86 V 57 87 W 58 88 X 59 89 Y 5a 90 Z
** Enter Setup 105 Hex Dec Char 5b 91 [ (Left / Opening Bracket) 5c 92 \ (Back Slash) 5d 93 ] (Right / Closing Bracket) 5e 94 ^ (Caret / Circumflex) 5f 95 _ (Underscore) 60 96 ' (Grave Accent) 61 97 A 62 98 B 63 99 C 64 100 d 65 101 e 66 102 f 67 103 g 68 104 h 69 105 i 6a 106 j 6b 107 k 6c 108 l 6d 109 m 6e 110 n 6f 111 o 70 112 p 71 113 q 72 114 r 73 115 s 74 116 t 75 117 u 76 118 v 77 119 w 78 120 x 79 12
** Enter Setup Hex Dec Char 7b 123 { (Left/ Opening Brace) 7c 124 | (Vertical Bar) 7d 125 } (Right/Closing Brace) 7e 126 ~ (Tilde) 7f 127 DEL (Delete)
** Enter Setup Digit Barcodes 0~5 107 0 1 2 3 4 5 Exit Setup
** Enter Setup 6~ 9 6 7 8 9
** Enter Setup A~F 109 A B C D E F Exit Setup
** Enter Setup Save/Cancel Barcodes After reading numeric barcode(s), you need to scan the Save barcode to save the data. If you scan the wrong digit(s), you can either scan the Cancel the Last Digit barcode and then the correct digit, or scan the Cancel All Digits barcode and then the digits you want. For instance, after reading the Decode Session Timeout barcode and numeric barcodes “1”, “2” and “3”, you scan: Cancel the Last Digit: The last digit “3” will be removed.
** Enter Setup F1~F12 When the USB HID-KBW feature is enabled, scanning one of the following barcodes will send the corresponding function key.
** Enter Setup F7~F12 F7 F8 F9 F10 F11 F12
