User manual
Operating instructions
Water fountain with LED
Item no. 1275878 (Happy Buddha)
Item no. 1275879 (Buddha)
Intended use
The product has been designed for outdoor use and is therefore suitable for decorating
a yard or patio. The pump included in the delivery scope pumps the water from inside
the gurine to a collection tank. The water can then run back again towards the inside
of the gurine, rendering a steady water supply unnecessary. The pump output is
adjustable. Connect to a mains socket for power supply.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
re, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Water fountain
• Pump
• Power adapter
• Decorative stones
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• The mains outlet must be located near to the device and be easily
accessible.
• Only use the supplied mains adapter as a power supply.
• Only connect the power adapter to a normal mains socket connected to
the public supply. Before plugging in the power adapter, check whether
the voltage stated on the power adapter complies with the voltage of your
electricity supplier.
• Never connect or disconnect power adapters if your hands are wet.
• Never unplug the power adapter from the mains socket by pulling on the
cable; always use the grips on the plug.
• When setting up the product, make sure that the cables are not pinched,
kinked or damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled
in them. This poses a risk of injury.
• For safety reasons, disconnect the power adapter from the mains socket
during storms.
• The power adapter is only splash proof when connected to a splash proof
wall socket.
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
• Never leave the product unattended during use.
• The two cables of the pump are not replaceable. If one of these two
cables has been damaged, the pump must be disposed of.
• Use the pump for this product only.
• The pump is only suitable for pumping water. Do not use any other liquids.
• The pump must be fully immersed in water. Switching on the pump when
not fully immersed will damage the pump. The pump must never draw in
air or run dry.
• Never reach into the water tank while the pump is switched on. First
disconnect the power adapter from the wall socket.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modications and repairs are to be performed exclusively
by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Operation
It is imperative that you follow the specied sequence during installation/
connection. Otherwise this poses a risk of fatal electric shock!
Do not directly connect the cable of the LED ring with the power adapter.
Connect the cable of the LED ring to the short cable of the pump only.
• Place the Buddha gurine on a at, stable ground.
• Guide the cable of the LED ring from above through the opening located closer to
the Buddha gurine.
• Guide the end of the pump hose (the end with the narrow, long connector) from
below through the same opening.
• Attach the LED ring to the end of the hose. The LEDs must be facing up.
• Insert the LED ring into the opening.
• Make sure the other end of the hose (the end with the wide, short connector) is
connected to the top of the pump.
• Connect the plug of the LED ring to the short cable of the pump. Secure the
connection using the cap nut.
• Connect the plug of the long cable of the pump to the proper socket on the power
adapter. Secure the connection using the cap nut.
• Centre the pump on the base inside the Buddha gurine. The hose connector must
be facing up.
• Fill the Buddha gurine with water. It is recommended to use distilled or ltered
(puried) water to achieve best possible performance.
Fill with water to a level of 7 cm at least. The maximum lling height is 15 cm
(item no. 1275878) / 20 cm (item no. 1275879).
• If desired, arrange the decorating stones around the LED ring and the water drain.
• Connect the power adapter to a suitable wall socket. The pump will then start
pumping water and the LED ring will light up.
The product does not feature a separate on/o switch. Disconnect the
power adapter from the wall socket in order to switch o the pump and LED
ring.
• The plume of water should be of approx. 2 – 3 cm in height. There is a lever located
on the side of the pump housing for adjusting the output of the pump.
- Move the lever to the left (+) to increase the pump output.
- Move the lever to the right (-) to reduce the pump output.