User manual

These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.
V2_0614_02-KV
Installation location
• Never install the product in a depression or hollow as puddles could form in these
places.
• Instead, install the product on a rm, horizontal and even surface from which
rainwater can run o without entering the housing of the product.
Operation
• Connect the power plug to an appropriate power outlet. The small chronometer (1)
within the timer starts rotating. A complete revolution of 360º equals one minute.
• Synchronize the timer with the current time.
- Wait for the full hour or until 15, 30 or 45 minutes after that.
- Turn the outer ring of the timer clockwise until the tip of the triangular arrow (3)
points at the current time.
- The image shows the arrow pointing at 8:15pm.
If the product is disconnected from the power supply, you must synchronize
the timer again.
• Use the 96 small levers to adjust the period in which the connected devices are to
be turned on.
- Press the levers outwards in order to set the period in which the connected
devices are to be activated. For example, use the tip of a pen or a small screwdriver
to do so. Proceed with caution and do not use any force, as the levers could break
away otherwise.
- When adjusting the levers as indicated in the image, the connected devices turn
on at 6:45 pm and turn o at 8:30 pm.
- For example, if you press every second lever outwards, the connected devices
turn on and o in intervals of 15 minutes.
• In order for the connected loads to be activated by the timer, the slide switch (4)
must be set to lower position .
• In order to turn on the connected loads permanently and regardless of the timer, set
the slide switch to upper position I.
• Once the sockets get activated (either via timer or slide switch), the ON/OFF
indicator (2) is at ONposition.
• Connect your switched o devices to the sockets. Guide the cables through the
intended recessions. Make sure the cables do not get jammed when closing the
cover of the housing.
• Turn on the connected devices.
Maintenance and cleaning
• This product does not require maintenance. There are no components located
inside the product you need to maintain. Never open/dismantle the product. Have
maintenance and repairs done by qualied experts or repair shops only.
• Never use any aggressive cleaning agents or chemical solutions as they may cause
damage to the housing or the product to malfunction.
• Never point any water jet, such as that of a high-pressure cleaner, at the product.
• Before each cleaning, disconnect the power plug of the product from the power
outlet and disconnect all connected loads from the product.
• Clean the housing with a slightly damp cloth. Use a few drops of a mild detergent in
case of heavy staining.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
You thus full your statutory obligations and contribute to the protection of
the environment.
Technical data
Nominal voltage ..................................250 V/AC, 50 Hz
Connected load/current ..................... max. 3680 W / 16 A
Protection type ....................................IP44
Cable type.............................................H07RN-F 3G 1.5 mm²
Shortest switching time .....................15 min
Operating conditions ..........................-25 to +40 ºC, <95 % RH
Storage conditions..............................-25 to +40 ºC, <95 % RH
Cable length .........................................5 m
Dimensions (W x H x D)......................200 x 215 x 200 mm
Weight ...................................................4 kg