Datasheet

78K0/Kx2-L APPENDIX C REVISION HISTORY
R01UH0028EJ0400 Rev.4.00 801
Sep 27, 2010
(4/8)
Edition Description Chapter
Modification of Caution in Figure 17-14 Format of Priority Specification Flag Registers
(PR0L, PR0H, PR1L, PR1H) (78K0/KB2-L) to Figure 17-16 Format of Priority
Specification Flag Registers (PR0L, PR0H, PR1L, PR1H) (48-pin products of
78K0/KC2-L)
CHAPTER 17
INTERRUPT
FUNCTIONS
Addition of Caution 4 to 19.1.1 (2) STOP mode
CHAPTER 19
STANDBY FUNCTION
Addition of 8-bit A/D conversion result register L (ADCRL) to Table 20-2 Hardware
Statuses After Reset Acknowledgment (3/4)
CHAPTER 20 RESET
FUNCTION
Addition of Note 5 to Figure 21-2 Timing of Generation of Internal Reset Signal by
Power-on-Clear Circuit and Low-Voltage Detector (2/2)
CHAPTER 21
POWER-ON-CLEAR
CIRCUIT
Modification of Note 4 in Figure 22-2 Format of Low-Voltage Detection Register (LVIM)
Modification of Figure 22-3 Format of Low-Voltage Detection Level Select Register
(LVIS), modification of Note 1
Modification of description in 22.4.1 (1) (b) When LVI default start function enabled is
set (LVISTART = 1) • When starting operation
Modification of description in 22.4.2 (1) (b) When LVI default start function enabled is
set (LVISTART = 1) • When starting operation
CHAPTER 22 LOW-
VOLTAGE
DETECTOR
Modification of Cautions 1 and 3 in Figure 23-1 Format of Regulator Mode Control
Register (RMC)
CHAPTER 23
REGULATOR
Modification of Caution in 24.1 (2) 0081H/1081H
Modification of Note 1 in Figure 24-1 Format of Option Byte (2/3)
Modification of Caution 2 in Figure 24-1 Format of Option Byte (3/3)
CHAPTER 24
OPTION BYTE
Addition of Note to Figure 25-2 Environment for Writing Program to Flash Memory
Addition of Note to Table 25-2 Pin Connection
Modification of 25.4.2 TOOLD0 and TOOLD1 pins
Modification of Caution 3 and Remark in 25.7 Flash Memory Programming by Self
Programming
CHAPTER 25 FLASH
MEMORY
Revision of Figure 26-1 Connection Example of QB-MINI2 and 78K0/Kx2-L
Microcontrollers
CHAPTER 26 ON-
CHIP DEBUG
FUNCTION
Modification of A/D converter pins in (2) Non-port functions
Modification of oscillation frequency (fIH) in Internal High-speed Oscillator
Characteristics
Modification of oscillation clock frequency (fIL = 30 kHz) in Internal Low-speed Oscillator
Characteristics
2nd Edition
DC Characteristics
• Deletion of pull-down resistor (R
PLD1)
• Modification of supply current (I
DD1, IDD2, IDD3)
• Modification of real-time counter operating current (I
RTC), TMH1 operating current (ITMH),
A/D converter operating current (I
ADC), and operational amplifier operating current (IAMP)
CHAPTER 28
ELECTRICAL
SPECIFICATIONS
(TARGET VALUES)
Remark “Classification” in the above table classifies revisions as follows.
(a): Error correction, (b): Addition/change of specifications, (c): Addition/change of description or note, (d):
Addition/change of package, part number, or management division, (e): Addition/change of related
documents