Datasheet

78K0/Kx2-L CHAPTER 28 ELECTRICAL SPECIFICATIONS
R01UH0028EJ0400 Rev.4.00 750
Sep 27, 2010
Caution The pins mounted depend on the product. Refer to Caution 2 at the beginning of this chapter.
DC Characteristics (7/8)
(T
A = −40 to +85°C, 1.8 V ≤ VDD ≤ 5.5 V, AVREF ≤ VDD, VSS = AVSS = 0 V)
Parameter Symbol Conditions MIN. TYP. MAX. Unit
Square wave input 1.6 2.8 mA fXH = 10 MHz,
V
DD = 5.0 V, RMC = 00H
Resonator connection 2.3 3.9 mA
Square wave input 1.5 2.7 mA fXH = 10 MHz,
V
DD = 3.0 V, RMC = 00H
Resonator connection 2.2 3.2 mA
Square wave input 0.9 1.6 mA fXH = 5 MHz,
V
DD = 3.0 V, RMC = 00H
Resonator connection 1.3 2.0 mA
Square wave input 0.7 1.4 mA fXH = 5 MHz,
V
DD = 2.0 V, RMC = 00H
Resonator connection 1.0 1.6 mA
fIH = 4 MHz
Note 4
, VDD = 3.0 V, RMC = 56H 0.5 1.4 mA
fIH = 8 MHz
Note 4
, VDD = 5.0 V, RMC = 00H 1.3 2.5 mA
fIH = 4 MHz
Note 4
, fCPU = 1 MHz,
Note 5
V
DD = 3.0 V, RMC = 56H
0.22 0.65 mA
TA = −40 to +50°C 3.0 6.3 μ A
TA = −40 to +70°C 3.0 7.5 μ A
IDD1
Note 2
Operating
mode
f
SUB = 32.768 kHz,
V
DD = 3.0 V,
RMC = 56H
Note 6
T
A = −40 to +85°C 3.0 9.7 μ A
Square wave input 0.4 1.3 mA fXH = 10 MHz,
V
DD = 5.0 V, RMC = 00H
Resonator connection 1.0 2.4 mA
Square wave input 0.2 0.65 mA fXH = 5 MHz,
V
DD = 3.0 V, RMC = 00H
Resonator connection 0.5 1.1 mA
fIH = 4 MHz
Note 4
, VDD = 3.0 V, RMC = 56H 0.2 0.5 mA
fIH = 8 MHz
Note 4
, VDD = 5.0 V, RMC = 00H 0.3 1.2 mA
TA = −40 to +50°C 0.98 3.2 μ A
TA = −40 to +70°C 0.98 4.8 μ A
IDD2
Note 2
HALT
mode
f
SUB = 32.768 kHz,
V
DD = 3.0 V,
RMC = 56H
Note 6
T
A = −40 to +85°C 0.98 6.7 μ A
TA = −40 to +50°C 0.3 2.7 μ A
TA = −40 to +70°C 0.3 3.7 μ A
Supply current
Note 1
I
DD3
Note 3
STOP
mode
VDD = 3.0 V, RMC = 56H
T
A = −40 to +85°C 0.3 5.5 μ A
Notes 1. Total current flowing into the internal power supply (VDD, AVREF), including the input leakage current flowing
when the level of the input pin is fixed to V
DD or VSS. However, the current flowing into the pull-up resistors,
the pull-down resistors and the output current of the port are not included.
2. Not including the current flowing into the oscillation circuit other than the circuit which generates the clock
supplied to CPU. Not including the current flowing into the LVI circuit, A/D converter, operational amplifier,
watchdog timer, real-time counter and 8-bits timer H1 (When using the 30 kHz internal low-speed oscillation
clock as the count clock).
3. Not including the current flowing into the LVI circuit, watchdog timer, real-time counter and 8-bits timer H1
(When using the 30 kHz internal low-speed oscillation clock as the count clock).
4. The internal high-speed oscillation clock frequency is set by option byte (R4M8MSEL = 0: 8 MHz, R4M8MSEL
= 1: 4 MHz).
5. This is the value when PCC2 = 0, PCC1 = 1, PCC0 = 0.
6. This is the value when a resonator is connected.
Remark Unless specified otherwise, the characteristics of alternate-function pins are the same as those of port pins.