Datasheet

CHAPTER 27 ELECTRICAL SPECIFICATIONS (STANDARD PRODUCTS)
User’s Manual U18698EJ1V0UD
545
Standard
p
roducts
DC Characteristics (1/5)
(TA = −40 to +85°C, 1.8 V ≤ VDD ≤ 5.5 V, AVREF ≤ VDD, VSS = AVSS = 0 V)
Parameter Symbol Conditions MIN. TYP. MAX. Unit
4.0 V ≤ VDD ≤ 5.5 V −3.0 mA
2.7 V ≤ VDD < 4.0 V −2.5 mA
Per pin for P12, P13,
P31 to P34, P40, P120
1.8 V ≤ V
DD < 2.7 V −1.0 mA
4.0 V ≤ VDD ≤ 5.5 V −0.1 mA
2.7 V ≤ VDD < 4.0 V −0.1 mA
Per pin for P100, P101,
P112, P113, P140 to P143,
P150 to P153
1.8 V ≤ V
DD < 2.7 V −0.1 mA
4.0 V ≤ VDD ≤ 5.5 V −20.0 mA
2.7 V ≤ VDD < 4.0 V −10.0 mA
Total
Note3
of P12, P13,
P31 to P34, P40, P120
1.8 V ≤ V
DD < 2.7 V −5.0 mA
4.0 V ≤ VDD ≤ 5.5 V −2.8 mA
2.7 V ≤ VDD < 4.0 V −2.8 mA
Total
Note3
of P100, P101,
P112, P113, P140 to P143,
P150 to P153
1.8 V ≤ V
DD < 2.7 V −2.8 mA
4.0 V ≤ VDD ≤ 5.5 V −22.8 mA
2.7 V ≤ VDD < 4.0 V −12.8 mA
IOH1
Total
Note3
of all pins
1.8 V ≤ V
DD < 2.7 V −7.8 mA
Output current, high
Note1
I
OH2 Per pin for P20 to P25 AVREF = VDD −0.1 mA
4.0 V ≤ VDD ≤ 5.5 V 8.5 mA
2.7 V ≤ VDD < 4.0 V 5.0 mA
Per pin for P12, P13,
P31 to P34, P40, P120
1.8 V ≤ V
DD < 2.7 V 2.0 mA
4.0 V ≤ VDD ≤ 5.5 V 0.4 mA
2.7 V ≤ VDD < 4.0 V 0.4 mA
Per pin for P100, P101,
P112, P113, P140 to P143,
P150 to P153
1.8 V ≤ V
DD < 2.7 V 0.4 mA
4.0 V ≤ VDD ≤ 5.5 V 20.0 mA
2.7 V ≤ VDD < 4.0 V 15.0 mA
Total
Note3
of P12, P13,
P31 to P34, P40, P120
1.8 V ≤ V
DD < 2.7 V 9.0 mA
4.0 V ≤ VDD ≤ 5.5 V 11.2 mA
2.7 V ≤ VDD < 4.0 V 11.2 mA
Total
Note3
of P100, P101,
P112, P113, P140 to P143,
P150 to P153
1.8 V ≤ V
DD < 2.7 V 11.2 mA
4.0 V ≤ VDD ≤ 5.5 V 31.2 mA
2.7 V ≤ VDD < 4.0 V 26.2 mA
IOL1
Total
Note3
of all pins
1.8 V ≤ V
DD < 2.7 V 20.2 mA
Output current, low
Note2
I
OL2 Per pin for P20 to P25 AVREF = VDD 0.4 mA
Notes 1. Value of current at which the device operation is guaranteed even if the current flows from VDD to an output pin.
2. Value of current at which the device operation is guaranteed even if the current flows from an output pin to GND.
3. Specification under conditions where the duty factor is 70% (time for which current is output is 0.7 × t and
time for which current is not output is 0.3 × t, where t is a specific time). The total output current of the pins
at a duty factor of other than 70% can be calculated by the following expression.
• Where the duty factor of I
OH is n%: Total output current of pins = (IOH × 0.7)/(n × 0.01)
<Example> Where the duty factor is 50%, I
OH = 20.0 mA
Total output current of pins = (20.0 × 0.7)/(50 × 0.01) = 28.0 mA
However, the current that is allowed to flow into one pin does not vary depending on the duty factor. A
current higher than the absolute maximum rating must not flow into one pin.
Remark Unless specified otherwise, the characteristics of alternate-function pins are the same as those of port pins.