To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.
Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office.
User’s Manual H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator HS2168ECN61H User’s Manual Renesas Microcomputer Development Environment System H8S Family / H8S/2100 Series Rev.2.00 2003.
Preface Thank you for purchasing this user system interface cable (HS2168ECN61H) for the Renesas’ original microcomputer H8S/2168 group. The HS2168ECN61H is a user system interface cable that connects an H8S/2168 group E6000 emulator (HS2168EPI61H; hereinafter referred to as the emulator) to the IC socket for a TFP-144 package on the user system.
Contents Section 1 Configuration....................................................................................1 Section 2 Connection Procedures ......................................................................3 2.1 2.2 2.3 2.4 2.5 Connecting User System Interface Cable to Emulator Station ......................................... 3 2.1.1 Connecting User System Interface Cable to Cable Body Connector................... 4 2.1.2 Connecting EIO Board 2 to Emulator................................
Section 1 Configuration CAUTION Use an NQPACK144SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-144 package IC socket on the user system. Figure 1 shows the configuration of the HS2168ECN61H user system interface cable for the TFP-144 package. To emulator station Screws (M2.6 x 6 mm) CTS screws (M3 x 6 mm) for fastening the emulator station Cable body EIO board 2 EIO board 1 Screws (M2.0 x 10 mm) (for fastening cable head) Screws (M2.
Table 1 lists the HS2168ECN61H components. Please make sure you have all of these components when unpacking. Table 1 HS2168ECN61H Components No. Component Quantity Remarks Includes coaxial cable and two EIO boards 1 Cable body 1 2 Cable head 1 3 IC socket 1 For the TFP-144 package 4 Socket cover 1 For installing a TFP-144 packaged MCU 5 Screws (M2.6 x 6 mm) 2 For fastening EIO board 2 6 Screws (M2.0 x 10 mm) 4 For fastening cable head 7 Screws (M2.
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part.
2.1.1 Connecting User System Interface Cable to Cable Body Connector After making sure the direction of the cable body connector is correct, firmly insert the cable body connector into the emulator station socket, and fasten the emulator station with two CTS screws (M3 × 6 mm) (figure 2).
2.1.2 6. Remove four screws at the side of the emulator station. Pull up and remove the cover of the emulator casing. Insert connector P5 of EIO board 2 into connector P5 in the emulator station. Fasten EIO board 2 with the provided two screws (M2.6 × 6 mm). Set up the coaxial cable, which has been connected to EIO board 2, into a gutter of the emulator station. Set the cover of the emulator station and fasten four screws. E6000 1. 2. 3. 4. 5.
2.1.3 1. 2. 3. 4. 5. 6. 6 Removing EIO Board 2 from Emulator Remove four screws from the side of the emulator station. Pull up and remove the cover of the emulator casing. Remove two screws (M2.6 × 6 mm) from EIO board 2. Remove EIO board 2 from connector P5 of the emulator station. Remove the coaxial cable, which has been connected to EIO board 2, from a gutter of the emulator station. Set the cover of the emulator station and fasten four screws.
2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST.
Use the guide pins provided to determine where to install the IC socket, as shown in figure 4. Pin 1 Guide pins 4 projections to apply epoxy resin adhesive to Bottom view of IC socket IC socket (NQPACK144SE manufactured by Tokyo Eletech Corporation) User system Figure 4 Location Setting of IC Socket 2.2.2 Soldering IC Socket After fastening, solder the IC socket for a TFP-144 package to the user system.
2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a TFP-144 package on the user system with pin 1 on the user system interface cable head, and insert the user system interface cable head into the IC socket on the user system, as shown in figure 5. 2.2.4 Fastening Cable Head CAUTION 1. Use a screwdriver whose head matches the screw head. 2. The tightening torque must be 0.054 N•m or less.
Fasten the user system interface cable head to the IC socket for a TFP-144 package on the user system with the four screws (M2.0 × 10 mm) provided. Each screw should be tightened a little at a time, alternating between screws on opposing corners. Take special care, such as manually securing the IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components. Screws (M2.
2.2.5 Fastening Cable Body Connect the cable body and EIO board 1 to the cable head. Removing Cable body Push the lower part of EIO board 1 with your fingers EIO board 1 Cable body Remove jig EIO board 1 Cable head User system Figure 6 Fastening Cable Body and EIO Board 1 When removing the cable body or EIO board 1, push the unfastening jigs. If the lower part of the cable body is pushed, EIO board 1 may be removed. Push the lower part of EIO board 1 with your fingers.
2.3 Recommended Dimensions for User System Mount Pad Figure 7 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for a TFP-144 package (NQPACK144SE: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 7 are somewhat different from those of the actual chip's mount pad. 0.40 X 35 = 14.00 ± 0.05 3.0 - Ø1.0 8.0 15.10 MAX 19.10 min 8.0 Unit: mm Figure 7 Recommended Dimensions for Mount Pad 12 0.40 X 35 = 14.00 ± 0.05 0.
2.4 Dimensions for User System Interface Cable Head 76.2 25.0 The dimensions for the user system interface cable head are shown in figure 8. 25.6 25.0 20.5 66.0 Unit: mm Tolerance: ±0.
2.5 Resulting Dimensions after Connecting User System Interface Cable 13.3 48.3 The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 9. Cable head User system IC socket (NQPACK144SE manufactured by Tokyo Eletech Corporation) Unit: mm Tolerance: ±0.
Section 3 Installing the MCU on the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening.
Screws (M2.
Section 4 User System Interface Circuit The microcomputer (H8S/2168) is installed in this user system interface cable for emulating the LPC function. An interface circuit, as shown in figure 11, is provided for the user system interface signal of the H8S/2168. Figure 12 and table 2 show the settings of switches.
Table 2 Settings of Switches Switch Number Pin 1 Side Pin 3 Side SW1 Port E7 SERIRQ SW2 Port E6 LCLK SW3 Port E5 LRESET_N SW4 Port E4 LFRAME_N SW5 Port E3 LAD3 SW6 Port E2 LAD2 SW7 Port E1 LAD1 SW8 Port E0 LAD0 SW9 Port D5 LPCPD_N SW10 Port D4 CLKRUN_N SW11 Port D3 GA20 SW12 Port D2 PME_N SW13 Port D1 LSMI_N SW14 Port D0 LSCI 18
Section 5 Verifying Operation 1. When using the E6000 emulator for the H8S/2168 group, turn on the emulator according to the procedures described in the H8S/2168 Group E6000 Emulator User's Manual (HS2168EPI61HE). 2. Verify the user system interface cable connections by accessing the external memory and ports to check the bus states of the pins with the MEMORY_FILL command (emulator command). If an error is detected, recheck the soldered IC socket and the location of pin 1. 3.
Section 6 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount pad for the user system IC socket are different from those of the MCU. 3. To avoid breaking wires in the cable body, do not place heavy or sharp metal objects on the user system interface cable. 4.
6. To prevent EMI noise, enclose the user system interface cable head in a case. The recommended material of the case is iron plated with nickel or resin plated with nickel inside. The case must be large enough to include the user system interface cable head, user system interface cable, and target system.
Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator User's Manual Publication Date: Rev.1.00, August 25, 2003 Rev.2.00, December 25, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co., Ltd. ©2003 Renesas Technology Corp. All rights reserved. Printed in Japan.
H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator HS2168ECN61H User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan
