User`s manual
Table Of Contents
- Cover
- Notes regarding these materials
- Contents
- Section 1 System Configuration
- Section 2 Connecting the Emulator to the User System
- 2.1 Connecting the Emulator to the User System
- 2.2 Connecting the Emulator to the User System by Using the EV-chip Unit
- 2.2.1 Connecting the EV-chip Unit to the Emulator
- 2.2.2 Connecting the E200F External Bus Trace Unit to the EV-chip Unit
- 2.2.3 Connecting the Probe Head to the EV-chip Unit
- 2.2.4 Connecting the E200F Emulation Memory Unit to the EV-chip Unit
- 2.2.5 Connecting the E200F External Bus Trace Unit, Emulation Memory Unit, and EV-chip Unit
- 2.2.6 Connecting the EV-chip Unit to the User System Interface Board
- 2.3 Connecting the Emulator to the User System by Using the H-UDI Port Connector
- 2.4 Installing the H-UDI Port Connector on the User System
- 2.5 Pin Assignments of the H-UDI Port Connector
- 2.6 Recommended Circuit between the H-UDI Port Connector and the MCU
- 2.7 Connecting the E200F External Bus Trace Unit with the User System
- 2.8 Installing the External Bus Trace Unit Connector
- 2.8.1 External Bus Trace Unit Connector Installed on the User System
- 2.8.2 Pin Assignments of the User System Connector
- 2.8.3 Recommended Foot Pattern
- 2.8.4 Restrictions on Component Installation
- 2.8.5 Pin Assignments of the External Bus Trace Unit Connector
- 2.8.6 Layout of the External Bus Trace Unit Connector
- 2.9 Connecting the External Bus Trace Unit to the User System
- 2.9.1 Connecting the E200F External Bus Trace Unit to the Emulator Main Unit
- 2.9.2 Connecting the E200F External Bus Trace Unit to the User System
- 2.9.3 Connecting the E200F Emulation Memory Unit to the Emulator Main Unit
- 2.9.4 Connecting the Emulation Memory Unit to the User System
- 2.9.5 Connecting the E200F External Bus Trace Unit, Emulation Memory Unit, and User System
- Section 3 Software Specifications when Using the SH7211
- 3.1 Differences between the SH7211 and the Emulator
- 3.2 Specific Functions for the Emulator when Using the SH7211
- 3.2.1 Event Condition Functions
- 3.2.2 Trace Functions
- 3.2.3 Notes on Using the JTAG (H-UDI) Clock (TCK) and AUD Clock (AUDCK)
- 3.2.4 Notes on Setting the [Breakpoint] Dialog Box
- 3.2.5 Notes on Setting the [Event Condition] Dialog Box and the BREAKCONDITION_ SET Command
- 3.2.6 Performance Measurement Function
- Section 4 User System Interface Circuits
- Colophon
27
Table 2.4 Pin Assignments of the External Bus Trace Unit Connector (cont)
Pin
No.
I/O
(CONT)
E200F
Trace I/F
Connector
Pin Name
SH7211
Signal
Name
Voltage
Meaning of Signal
Note
82 IO UD-P33 _RASU 3.3 V SDRAM _RASU
signal
Connect the _RASU signal of the MPU (fix
_RASU to high level when it is not used).
83 IO UD-P34 _CASL 3.3 V SDRAM _CASL
signal
Connect the _CASL signal of the MPU (fix
_CASL to high level when it is not used).
84 IO UD-P35 _CASU 3.3 V SDRAM _CASU
signal
Connect the _CASU signal of the MPU (fix
_CASU to high level when it is not used).
85 IO UD-P36 N.C -
86 IO UD-P37 N.C -
87 IO UD-P38 N.C -
88 IO UD-P39 _DQMUU 3.3 V Most-upper-byte
signal of SDRAM
(D31-D24)
Connect the _DQMUU signal of the MPU (fix
_DQMUU to high level when it is not used).
89 - GND GND GND
90 - GND GND GND
91 IO UD-P40 RD_WR 3.3 V Read/write signal Connect the RD_WR signal of the MPU
(necessary).
92 IO UD-P41 N.C -
93 IO UD-P42 N.C -
94 IO UD-P43 N.C -
95 IO UD-P44 N.C -
96 IO UD-P45 N.C -
97 IO UD-P46 N.C -
98 IO UD-P47 N.C -
99 - GND GND GND
100 - GND GND GND
101 IO UD-P48 IRQ0 3.3 V Interrupt Connect the IRQ0 signal of the MPU (fix IRQ0 to
high level when it is not used).
102 IO UD-P49 IRQ1 3.3 V Interrupt Connect the IRQ1 signal of the MPU (fix IRQ1 to
high level when it is not used).
103 IO UD-P50 IRQ2 3.3 V Interrupt Connect the IRQ2 signal of the MPU (fix IRQ2 to
high level when it is not used).