User`s manual

RX62N Group, RX621 Group 4. Library Reference
Multi-function
Timer pulse unit
1
R_MTU2_Set
Configure the Multi-function Timer Pulse Units.
2
R_MTU2_Create
Configure a MTU channel.
3
R_MTU2_Destroy
Disable a Multi-function Timer Pulse Unit.
4
R_MTU2_ControlChannel
Control an MTU channel.
5
R_MTU2_ControlUnit
Control a Multi-function Timer Pulse Unit.
6
R_MTU2_ReadChannel
Read from MTU channel registers.
7
R_MTU2_ReadUnit
Read from MTU registers.
Port Output
Enable
1
R_POE_Set
Configure the Port Output Enable module.
2
R_POE_Create
Configure the Port Output Enable event handling.
3
R_POE_Control
Control the Port Output Enable module.
4
R_POE_GetStatus
Check the status of the Port Output Enable module.
Programmable
Pulse Generator
1
R_PPG_Create
Configure a PPG group.
2
R_PPG_Destroy
Disable a PPG unit.
3
R_PPG_Control
Control a PPG group.
8-bit Timer
1
R_TMR_Set
Configure the optional TMR pins.
2
R_TMR_CreateChannel
Configure a TMR timer channel.
3
R_TMR_CreateUnit
Configure a TMR timer unit.
4
R_TMR_CreatePeriodic
Select periodic operation.
5
R_TMR_CreateOneShot
Configure and use a one-shot timer.
6
R_TMR_Destroy
Disable a TMR timer unit.
7
R_TMR_ControlChannel
Write to timer channel registers.
8
R_TMR_ControlUnit
Write to timer unit registers.
9
R_TMR_ControlPeriodic
Control periodic operation.
10
R_TMR_ReadChannel
Read from timer channel registers.
11
R_TMR_ReadUnit
Read from timer unit registers.
Compare Match
Timer
1
R_CMT_Create
Configure a CMT channel.
2
R_CMT_CreateOneShot
Configure a CMT channel as a one-shot event.
3
R_CMT_Destroy
Disable a CMT unit.
4
R_CMT_Control
Control CMT operation.
5
R_CMT_Read
Read CMT channel status and registers.
Real-time Clock
1
R_RTC_Create
Configure the Real-time clock.
2
R_RTC_Control
Modify the Real-time clock operation.
3
R_RTC_Read
Read the Real-time clock status flags and counters.
Watchdog Timer
1
R_WDT_Create
Configure the Watchdog timer.
2
R_WDT_Control
Control the Watchdog operation.
3
R_WDT_Read
Read the Watchdog timer status and registers.
Independent
Watchdog Timer
1
R_IWDT_Set
Configure the Independent Watchdog operation.
2
R_IWDT_Control
Control the Independent Watchdog operation.
3
R_IWDT_Read
Read the watchdog timer status and counter.
Serial
Communication
Interface
1
R_SCI_Set
Configure the SCI pin selection.
2
R_SCI_Create
SCI channel setup.
3
R_SCI_Destroy
Shut down a SCI channel.
4
R_SCI_Send
Send a string of characters.
5
R_SCI_Receive
Receive a string of characters.
6
R_SCI_Control
Control the SCI channel.
7
R_SCI_GetStatus
Check the status of a SCI channel.
CRC calculator
1
R_CRC_Create
Configure the CRC calculator.
2
R_CRC_Destroy
Shut down the CRC calculator.
3
R_CRC_Write
Write data into the CRC calculation register.
4
R_CRC_Read
Read the CRC calculation result.
I²C bus interface
1
R_IIC_Create
I²C channel setup.
2
R_IIC_Destroy
Disable an I²C channel.
3
R_IIC_MasterSend
Write data to a slave device.
4
R_IIC_MasterReceive
Read data from a slave device.
5
R_IIC_MasterReceiveLast
Complete a DMAC or DTC-based read process.
6
R_IIC_SlaveMonitor
Monitor the bus and receive data from a master.
7
R_IIC_SlaveSend
Write data to a master device.
8
R_IIC_Control
I²C channel control.
9
R_IIC_GetStatus
Read the status for an I²C channel.
R20UT0084EE0112 Rev.1.12 Page 4-2
July. 16, 2014