User`s manual

RX62N Group, RX621 Group 4. Library Reference
Description (2/3)
•
Start trigger forwarding
PDL_DMAC_TRIGGER_CLEAR or
PDL_DMAC_TRIGGER_FORWARD
When the DMAC transfer is complete, clear the
DMAC activation trigger or pass it on to the CPU.
•
DTC trigger control
PDL_DMAC_DTC_TRIGGER_DISABLE or
PDL_DMAC_DTC_TRIGGER_ENABLE
Disable or enable activation of the DTC when
an event specified in the "Interrupt generation"
options occurs.
[data3]
Select one activation source for channel DMAn.
•
Trigger selection
Name
Trigger cause
PDL_DMAC_TRIGGER_SW or
By software.
PDL_DMAC_TRIGGER_CMT0 or
Compare match on channel CMTn
(n = 0 to 3).
PDL_DMAC_TRIGGER_CMT1 or
PDL_DMAC_TRIGGER_CMT2 or
PDL_DMAC_TRIGGER_CMT3 or
PDL_DMAC_TRIGGER_USB0_D0 or
D0FIFO transfer request on USB port n (n = 0 to 1).
PDL_DMAC_TRIGGER_USB1_D0 or
PDL_DMAC_TRIGGER_USB0_D1 or
D1FIFO transfer request on USB port n (n = 0 to 1).
PDL_DMAC_TRIGGER_USB1_D1 or
PDL_DMAC_TRIGGER_SPI0_RX or
Receive buffer full on RSPI channel n (n = 0 to 1).
PDL_DMAC_TRIGGER_SPI1_RX or
PDL_DMAC_TRIGGER_SPI0_TX or
Transmit buffer empty on RSPI channel n
(n = 0 to 1).
PDL_DMAC_TRIGGER_SPI1_TX or
PDL_DMAC_TRIGGER_IRQ0 or
Valid edge detected on pin IRQn (n = 0 to 3).
PDL_DMAC_TRIGGER_IRQ1 or
PDL_DMAC_TRIGGER_IRQ2 or
PDL_DMAC_TRIGGER_IRQ3 or
PDL_DMAC_TRIGGER_ADC10_0 or
Conversion completed on 10-bit ADC unit n
(n = 0 to 1).
PDL_DMAC_TRIGGER_ADC10_1 or
PDL_DMAC_TRIGGER_ADC12 or
Conversion completed on 12-bit ADC unit.
PDL_DMAC_TRIGGER_MTU0 or
Input capture or compare match on MTU channel n
(n = 1 to 4 or 6 to 10).
PDL_DMAC_TRIGGER_MTU1 or
PDL_DMAC_TRIGGER_MTU2 or
PDL_DMAC_TRIGGER_MTU3 or
PDL_DMAC_TRIGGER_MTU4 or
PDL_DMAC_TRIGGER_MTU6 or
PDL_DMAC_TRIGGER_MTU7 or
PDL_DMAC_TRIGGER_MTU8 or
PDL_DMAC_TRIGGER_MTU9 or
PDL_DMAC_TRIGGER_MTU10 or
PDL_DMAC_TRIGGER_SCI0_RX or
Receive buffer full on SCI channel n
(n = 0 to 3 or 5 to 6).
PDL_DMAC_TRIGGER_SCI1_RX or
PDL_DMAC_TRIGGER_SCI2_RX or
PDL_DMAC_TRIGGER_SCI3_RX or
PDL_DMAC_TRIGGER_SCI5_RX or
PDL_DMAC_TRIGGER_SCI6_RX or
PDL_DMAC_TRIGGER_SCI0_TX or
Transmit buffer empty on SCI channel n
(n = 0 to 3 or 5 to 6).
PDL_DMAC_TRIGGER_SCI1_TX or
PDL_DMAC_TRIGGER_SCI2_TX or
PDL_DMAC_TRIGGER_SCI3_TX or
PDL_DMAC_TRIGGER_SCI5_TX or
PDL_DMAC_TRIGGER_SCI6_TX or
PDL_DMAC_TRIGGER_IIC0_RX or
Receive buffer full on I²C channel n (n = 0 to 1).
PDL_DMAC_TRIGGER_IIC1_RX or
PDL_DMAC_TRIGGER_IIC0_TX or
Transmit buffer empty on I²C channel n (n = 0 to 1).
PDL_DMAC_TRIGGER_IIC1_TX
[data4]
The source start address.
R20UT0084EE0112 Rev.1.12 Page 4-65
July. 16, 2014