Datasheet
R01DS0052EJ0140 Rev.1.40 Page 91 of 150
2014.07.16
RX62N Group, RX621 Group 5. Electrical Characteristics
Note 1. The VIH characteristic of the pins multiplexed with 5-V tolerant ports 00 to 02, 07, 12, 13, 16, 17, 20, 21, and 33 is the same as
the V
IH characteristic of 5-V tolerant ports.
Note 2. Supply current values are with all output pins unloaded and all input pull-up MOSs in the off state.
Note 3. Measured with clocks supplied to the peripheral functions. This does not include the BGO operation.
Note 4. ICC depends on f (ICLK) as follows. (ICLK: PCLK: BCLK: BCLK pin = 8 : 4: 8: 4)
ICC max. = 0.89 x f + 11 (max.)
ICC typ. = 0.43 x f + 5 (normal operation, peripheral function: clocks supplied)
ICC typ. = 0.30 x f + 5 (normal operation, peripheral function: clocks not supplied)
ICC max. = 0.48 x f + 12 (sleep mode)
Note 5. This does not include the BGO operation.
Note 6. Incremented if data is written to or erased from the ROM or data flash for data storage during the program execution.
Note 7. The values are for reference.
Table 5.4
DC Characteristics (3)
Conditions: VCC = PLLVCC = AVCC = VCC_USB = 2.7 to 3.6 V, VREFH = 2.7 V to AVCC
VSS = PLLVSS = AVSS = VREFL = VSS_USB = 0 V
T
a
= -40 to +85C
Item Symbol Min. Typ. Max. Unit Test Conditions
Supply
current
*2
In
operation
Max.
*3
I
CC
*4
— — 100 mA ICLK = 100 MHz
PCLK = 50 MHz
BCLK = 50 MHz
Normal
operation
Peripheral function:
Clocks supplied
*5
—48—
Peripheral function:
Clocks not supplied
*5
—35—
Increased by BGO operation
*6
—15—
Sleep — 20 60
All-module-clock-stop mode
*7
—1428
Standby
mode
Software standby mode — 0.12 3.0 mA
Deep software
standby mode
RTC in
operation
RAM,
USB
retained
— 30 206 µA
RAM,
USB
power
supply
halted
—2666µA
RTC
halted
RAM,
USB
retained
— 25 200 µA
RAM,
USB
power
supply
halted
—2160µA
Analog
power
supply
current
During 12-bit A/D conversion (per unit) AI
CC
—2.53.0mA
During 10-bit A/D conversion (per unit) — 0.8 1.2 mA
During D/A conversion (per channel) — 0.3 2.0 µA
Idle (all units) — 30 35 µA
During A/D or D/A standby (all units) — 0.1 4.0 µA
Reference
power
supply
current
During 12-bit A/D conversion (per unit) AI
CC
—0.50.7mA
During 10-bit A/D conversion (per unit) — 0.06 0.1 mA
During D/A conversion (per channel) — 0.6 1.0 mA
Idle (all units) — 0.4 0.6 mA
During A/D or D/A standby (all units) — 0.1 2.0 µA
RAM standby voltage V
RAM
2.48 — — V
VCC rising gradient SVCC — — 20 ms/V