Datasheet

R8C/36C Group 5. Electrical Characteristics
R01DS0018EJ0110 Rev.1.10 Page 39 of 59
Nov 02, 2010
Notes:
1. V
CC = 1.8 to 5.5 V and Topr = −20 to 85 °C (N version)/−40 to 85 °C (D version), unless otherwise specified.
2. This enables the setting errors of bit rates such as 9600 bps and 38400 bps to be 0% when the serial interface is used in
UART mode.
Note:
1. V
CC = 1.8 to 5.5 V and Topr = −20 to 85 °C (N version)/−40 to 85 °C (D version), unless otherwise specified.
Notes:
1. The measurement condition is V
CC = 1.8 to 5.5 V and Topr = 25 °C.
2. Waiting time until the internal power supply generation circuit stabilizes during power-on.
Table 5.12 High-speed On-Chip Oscillator Circuit Electrical Characteristics
Symbol Parameter Condition
Standard
Unit
Min. Typ. Max.
— High-speed on-chip oscillator frequency after
reset
V
CC = 1.8 V to 5.5 V
−20 °C ≤ T
opr ≤ 85 °C
38.4 40 41.6 MHz
V
CC = 1.8 V to 5.5 V
−40 °C ≤ T
opr ≤ 85 °C
38.0 40 42.0 MHz
High-speed on-chip oscillator frequency when the
FRA4 register correction value is written into the
FRA1 register and the FRA5 register correction
value into the FRA3 register
(2)
VCC = 1.8 V to 5.5 V
−20 °C ≤ T
opr ≤ 85 °C
35.389 36.864 38.338 MHz
V
CC = 1.8 V to 5.5 V
−40 °C ≤ T
opr ≤ 85 °C
35.020 36.864 38.707 MHz
High-speed on-chip oscillator frequency when the
FRA6 register correction value is written into the
FRA1 register and the FRA7 register correction
value into the FRA3 register
V
CC = 1.8 V to 5.5 V
−20 °C ≤ T
opr ≤ 85 °C
30.72 32 33.28 MHz
V
CC = 1.8 V to 5.5 V
−40 °C ≤ T
opr ≤ 85 °C
30.40 32 33.60 MHz
— Oscillation stability time V
CC = 5.0 V, Topr = 25 °C—0.53ms
— Self power consumption at oscillation V
CC = 5.0 V, Topr = 25 °C — 400 — µA
Table 5.13 Low-speed On-Chip Oscillator Circuit Electrical Characteristics
Symbol Parameter Condition
Standard
Unit
Min. Typ. Max.
fOCO-S Low-speed on-chip oscillator frequency 60 125 250 kHz
— Oscillation stability time V
CC = 5.0 V, Topr = 25 °C — 30 100 µs
— Self power consumption at oscillation V
CC = 5.0 V, Topr = 25 °C— 2 — µA
Table 5.14 Power Supply Circuit Timing Characteristics
Symbol Parameter Condition
Standard
Unit
Min. Typ. Max.
t
d(P-R) Time for internal power supply stabilization during
power-on
(2)
— — 2,000 µs