Datasheet

RL78/G13 1. OUTLINE
Page 48 of 194R01DS0131EJ0310 Rev.3.10
Nov 15, 2013
1.6 Outline of Functions
[20-pin, 24-pin, 25-pin, 30-pin, 32-pin, 36-pin products]
Caution This outline describes the functions at the time when Peripheral I/O redirection register (PIOR)
is set to 00H.
(1/2)
Item 20-pin 24-pin 25-pin 30-pin 32-pin 36-pin
R5F1006x R5F1016x R5F1007x R5F1017x R5F1008x R5F1018x
R5F100Ax R5F101Ax R5F100Bx R5F101Bx
R5F100Cx R5F101Cx
Code flash memory (KB) 16 to 64 16 to 64 16 to 64 16 to 128 16 to 128 16 to 128
Data flash memory (KB) 4 − 4 − 4 − 4 to 8 − 4 to 8 − 4 to 8 −
RAM (KB)
2 to 4
Note1
2 to 4
Note1
2 to 4
Note1
2 to 12
Note1
2 to 12
Note1
2 to 12
Note1
Address space 1 MB
Main system
clock
High-speed system
clock
X1 (crystal/ceramic) oscillation, external main system clock input (EXCLK)
1 to 20 MHz: V
DD = 2.7 to 5.5 V, 1 to 8 MHz: VDD = 1.8 to 2.7 V, 1 to 4 MHz: VDD = 1.6 to 1.8 V
High-speed on-chip
oscillator
HS (High-speed main) mode: 1 to 32 MHz (VDD = 2.7 to 5.5 V),
HS (High-speed main) mode: 1 to 16 MHz (V
DD = 2.4 to 5.5 V),
LS (Low-speed main) mode: 1 to 8 MHz (V
DD = 1.8 to 5.5 V),
LV (Low-voltage main) mode: 1 to 4 MHz (V
DD = 1.6 to 5.5 V)
Subsystem clock −
Low-speed on-chip oscillator 15 kHz (TYP.)
General-purpose registers (8-bit register × 8) × 4 banks
Minimum instruction execution time 0.03125 μ s (High-speed on-chip oscillator: fIH = 32 MHz operation)
0.05 μ s (High-speed system clock: fMX = 20 MHz operation)
Instruction set
• Data transfer (8/16 bits)
• Adder and subtractor/logical operation (8/16 bits)
• Multiplication (8 bits × 8 bits)
• Rotate, barrel shift, and bit manipulation (Set, reset, test, and Boolean operation), etc.
I/O port Total 16 20 21 26 28 32
CMOS I/O
13
(N-ch O.D. I/O
[V
DD withstand
voltage]: 5)
15
(N-ch O.D.
I/O [V
DD
withstand
voltage]: 6)
15
(N-ch O.D.
I/O [V
DD
withstand
voltage]: 6)
21
(N-ch O.D.
I/O [V
DD
withstand
voltage]: 9)
22
(N-ch O.D.
I/O [V
DD
withstand
voltage]: 9)
26
(N-ch O.D.
I/O [V
DD
withstand
voltage]: 10)
CMOS input 3 3 3 3 3 3
CMOS output − − 1 − − −
N-ch O.D. I/O
(withstand voltage:
6 V)
− 2 2 2 3 3
Timer 16-bit timer 8 channels
Watchdog timer 1 channel
Real-time clock (RTC)
1 channel
Note 2
12-bit interval timer (IT) 1 channel
Timer output
3 channels
(PWM outputs:
2
Note 3
)
4 channels
(PWM outputs: 3
Note 3
)
4 channels (PWM outputs: 3
Note 3
),
8 channels (PWM outputs: 7
Note 3
)
Note 4
RTC output −
Notes 1. In the case of the 4 KB, this is about 3 KB when the self-programming function and data flash
function are used. (For details, see CHAPTER 3
in the RL78/G13 User’s Manual Hardware )
2. Only the constant-period interrupt function when the low-speed on-chip oscillator clock (f
IL) is
selected
3. The number of PWM outputs varies depending on the setting of channels in use (the number of
masters and slaves). (6.9.3 Operation as multiple PWM output function
in the RL78/G13 User’s
Manual Hardware
)
4. When setting to PIOR = 1